HQ-Power VDP1500HZ Manual Del Usuario página 4

• Only u use the device fo
electro oshocks, crash,
• The in stallation has to
4. Ins stallation
• Clean the spray nozzl
• Place t the VDP1500H
• Be car reful when filling
back o on the tank and
• Conne ct the remote c
5. Use e
The Haz ze Machine
• Plug th he haze machin
• Turn o on haze machine
• The de evice can work o
• The de evice must warm
minute es.
The Rem mote Control
• The re emote controller
1 UP key
2 LCD D display
3 FUN NCTION key
4 DOW WN key
ADD
MU
SE
VO
OUTPUT
DMX512 2 Connection
Connect the provided XL
the male 3-pin XLR inpu
linking. T The linking cable
DMX512 2 Chain with Te
DMX Sta art Address
All DMX-c controlled devic
This start t address is the
Enter the e correct numbe
You can u use the same st
device. W When all devices
on one p articular channe
simultane eously. If you s
Changing g the settings of
01.06.201 0
or its intended p purpose. All oth
etc. Using the d device in an una
o be approved b by an expert bef
e and make sur re nothing is ob
HZ horizontally o on a flat surface
g the tank and d do not exceed th
tighten.
controller into th he slot at the ba
e into the main s using the pow
e using the pow wer switch locate
on a DMX512 si gnal via the 3/5
m up. The perio d depends on th
r is connected a t the back of th
DMX address
Minute time b between 2 outpu
Adjust the du uration of each o
Volume of sm moke output with
Timer functio n, allows you to
Press to start t or stop the sm
To lock the co ontroller setting
Timer directio on, when sparki
LR cable to the f female 3-pin XL
t of the VDP15 500HZ. Multiple
e should be a tw wo-core screene
ermination
A DMX termin nator is recomm
to run a long distance or is in
The terminato or prevents corr
noise. The DM MX terminator is
between pins 2 and 3, which
last device in the chain.
Please see illu ustrations.
ces need a digita al start address
channel numbe er from which th
er and read it fro om the display
tarting address for a whole gro
s have the same e address, all th
el. In other wor ds: changing th
et different add resses, each de
f one channel w will only affect th
VDP150 00HZ
er uses may lea
authorised way
fore the device
structing the ou
e. Remove the li
he maximum le
ack of the device
wer cable.
ed at the back.
5-pin XLR in/out
he condition but
e device.
5 TIMER k
6 OUTPUT
7 LOCK ke
uts
output emission
h 10% increasin
o set the operat
oke output.
s
ng the function
LR output of you
e VDP1500HZs
ed cable with XL
ended for insta
n an electrically
ruption of the di
s simply an XLR
is then plugged
so that the cor
he device starts
located on the b
oup of devices o
he VDP1500HZ
he settings of on
evice will "listen
he device in que
4
ad to short circu uits, burns,
will void the wa arranty.
is taken into se rvice.
utput.
iquid tank cap.
vel. Do not ove rfill. Place the c
e.
tput connectors s at the back.
t should not tak ke more than 10
key
T key
ey
ng.
ion time of the machine.
is running, if n ot it is closed.
ur controller and d the other side
can be linked t through serial
LR input and out tput connectors
llations where t he DMX cable h
noisy environm ment (e.g. discos
gital control sig gnal by electrica
plug with a 120 0 Ω resistor
d into the XLR o output socket of
rrect device resp ponds to the sig
s to "listen" to th he DMX controll
base of the VDP P1500HZ.
r enter an indiv vidual one for ev
Zs will "listen" to o the control sig
ne channel will a affect all device
" to a separate channel numbe
estion.
Rev v. 01
cap
0
e to
s.
has
s).
l
f the
gnals.
ler.
very
gnal
s
er.
©Vellema an nv