Starmix T 500 Instrucciones De Montaje página 11

cover plate. Insert the supplied mains terminal q. Cut
the plug off the power supply cable 5.
Remove the cable sheath and conductor insulation, and
crimp on the wire end sleeves. Connect the two con-
ductors as shown in fig. C. Ensure that L (brown) and N
(blue) are correctly connected. Secure the connecting
cable of the appliance-with the supplied strain relief
clamp 8.
Push the appliance right down onto the cover plate and
secure with the 2 supplied countersunk sheet metal
screws.
3.3 Connection from above by way of surface-mounted
wiring:
Break out the lead-through 9 at the top in the middle
of the back of the appliance. Fasten the mounting
plate 2 as indicated in fig. C. Conduct the surface-
mounted cable on the mounting plate down to the cover
plate 1 and pass it through the hole.
Connect as described in section 3.2.2.
3.4 Connection from below by way of surface-mounted
wiring:
Break out the predetermined lead-through 9 at the
bottom in the middle of the cover plate 1. Fasten the
mounting plate 2 as indicated in fig. C. Conduct the
surface-mounted cable through the opening in the cover
plate. Connect as described in section 3.2.2.
3.5 Connection by way of power supply cable with plug:
Connection to an adjacent mains socket by way of a
flexible power supply cable with plug. For this purpose
break out the predetermined lead-through 9 at the
bottom in the middle of the cover plate 9. Push the
cover plate from underneath into the mounting plate.
Insert the supplied mains terminal q.
Cut the plug off the power supply cable 5 of the
appliance. Remove the cable sheath and conductor
insulation and crimp on the wire end sleeves. Prepare
the free end of the power supply cable with plug in the
same manner, and conduct it through the opening in the
cover plate. Connect the two cables as indicated in
fig. C., and secure with the 2 supplied strain relief
clamps 8.
Push the appliance right down onto the cover
plate and secure with the 2 supplied countersunk sheet
metal screws.
The appliance is now ready for operation.
6. Switching functions.
T 500, TH 500 Z
Actuate the electronic short-duration timer on the T 500 and
TH 500 Z. Timer running time on the T 500 32 sec. on
the TH 500 Z 4 min.
The appliances are automatically switched off.
The timer running time on the TH 500Z can be changed by
a specialist. It is adjustable in 9 settings from 1–9 min. For
this purpose insert the screwdriver pin in the hole on the
left-hand side of the air intake grille 8 and turn the built-in
switch anti-clockwise to 3–2–1 min., or clock wise to
5–6–7–8–9 min.
The O-position of the switch is a blind setting in which the
appliance will not operate.
T 500 E, TH 500 E
The appliances are switched ON/OFF by an electronic
infrared proximity switch.
The switch spacing between the bottom edge of the
appliance and the hands or head for the T 500 is approx.
15 cm, and for the TH 500 approx. 40 cm. The switching
sensitivity can be changed by a specialist. For this purpose
insert the screwdriver pin in the opening on the left-hand
side of the air intake grille 8 and turn the built-in potentio-
meter anti-clockwise to reduce the sensitivity, or clockwise
to increase the sensitivity. Bright rooms require a lower
sensitivity setting.
TH 500
This appliance is supplied without switch. It can be
operated by the MZS 4 coinoperated timer, a normal
ON/OFF switch or a wall-mounted timer. It is mounted on
the wall at the same level as the appliance and connected
according to the circuit diagram, see fig. E or F.
T 500 E, TH 500 E sensor safety switch off
The built-in electronic safety circuit prevents continuous
operation in the event that the infrared proximity switch is
covered, e.g. chewing-gum, vandalism.
T 500 models switch off after 2 minutes, and TH 500
models after 10. The dryers are once again operable as soon
as the fault has been remedied.
MZS 4 coin-operated timer
The function of the power-saving electronic switch and the
proximity switch are retained when the TH 500 Z/E hair
dryers are operated with a coin-operated timer. Installation
of the MZS 4 will ensure that the cost of the hair dryers will
be quickly refunded and protect the appliance against
improper use.
11