General; Model Identification; Intended Use - WALTHER PILOT Trend Instrucciones De Servicio

Repair kits
For the manual spray guns PILOT Trend and -MP WALTHER has repair sets with all
wearing parts available. The parts are marked in bold in the spare parts list.
PILOT TREND Standard-version
Gravity-feed cup
PILOT TREND Standard-version
Material Connection
PILOT TREND-MP Medium-pressure version
Gravity-feed cup
PILOT TREND-MP Medium-pressure version
Material Connection
Nozzle sizes optional: ▪ 0,5 ▪ 0,8 ▪ 1,0 ▪ 1,2 ▪ 1,5 ▪ 1,8 ▪ 2,0 ▪ 2,5 mm ø
Nozzle kits
The nozzle kits consist of air head, material nozzle and material needle.
PILOT TREND Gravity-feed cup
PILOT TREND Material Connection
PILOT TREND-MP Gravity-feed cup
PILOT TREND-MP Material Connection
Nozzle sizes optional: ▪ 0,5 ▪ 0,8 ▪ 1,0 ▪ 1,2 ▪ 1,5 ▪ 1,8 ▪ 2,0 ▪ 2,5 mm ø
* When ordering replacements please quote the respective sizes.
We recommend to keep repair kits on stock.
Part No.
V 16 060 03 ..3*
V 16 062 03 ..3*
V 16 061 04 ..3*
V 16 063 04 ..3*
Part No.
V 15 060 03 ..3*
V 15 062 03 ..3*
V 15 061 04 ..3*
V 15 063 04 ..3*
24
1

General

1.1

Model Identification

Model: Manual Spray Gun PILOT Trend
Typ: PILOT Trend
PILOT Trend
PILOT Trend-MP
PILOT Trend-MP
Hersteller: WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18-30
D-42327 Wuppertal
Tel.: +202 / 787-0
Fax: +202 / 787-2217
www.walther-pilot.de • Email: info@walther-pilot.de
1.2

Intended use

The manual spray guns PILOT Trend and -MP are designed to be used exclusively
for sprayable media, such as:
• paints and lacquers
• greases, oils and corrosion preventives
• ceramic glazes
Aggressive materials shoudn't be sprayed.
If the material you intend to spray is not included in the above list, please contact
WALTHER Spritz- und Lackiersysteme GmbH, Wuppertal, for further information.
Please note that sprayable materials may only be applied to workpieces and /or simi-
lar objects.
The temperature of the spraying material must not exceed 43°C.
The term "normal use" also implies that all safety warnings, operating handling
details, etc., as stated in these operating instructions are carefully read, understood
and duly complied with.
This equipment complies with the explosion protection requirements of Directive
94/9/EC (ATEX) for the explosion group, equipment category and temperature class
indicated on the type plate. When using the equipment, the requirements specified in
these Operating Instructions must be observed at all times.
The technical data indicated on the equipment rating plates and the specifications in
the chapter "Technical Data" must be complied with at all times and must not be
exceeded. An overloading of the equipment must be ruled out.
The equipment may be used in potentially explosive atmospheres only with the
authorisation of the relevant supervisory authority.
The relevant supervisory authority or the operator of the equipment are
responsible for determining the explosion hazard (zone classification).
Gravity-Feed Cup V 10 601
Material Connection V 10 602
Gravity-Feed Cup V 10 611
Material Connection V 10 613
25