ROBBE Sport Wing 3281 Instrucciones De Montaje página 3

Parts List
Part No. Description
1 Main spar
 Wing
3 Landing skid
D1 - D5 Decals
4 Fuselage nose fairing
5 Elevon servo
6 Servo output arm
7 Swivel pushrod connector
8 Starlock washer
9 Control surface horn
10 Elevon pushrod
11 Servo well cover
1 Recessed hand-grip
13 C.G. indicator
14 Hinge tape
15 Winglet
16 Velcro dot
17 Velcro dot
18 RC compartment cover (glider)
19 Velcro tape
0 Velcro tape
1 Receiver
 Receiver battery
Contents, power set, No. 3284
3 Side panel
4 Front base plate
5 Rear base plate
6 Motor bulkhead
7 Doubler
8 Velcro dot
9 Velcro dot
30 Captive nut
31 Rubber grommet
3 Washer
33 Countersunk screw
34 Folding propeller, K1 - K7
35 Power system
36 Cable tie
37 Canopy
38 Flight battery
© robbe Modellsport
Assembly and operating instructions
Material Size in mm
Plywood 4, ready made
Lightweight foam Ready made
Plywood 4, ready made
Plastic Sheet
Plastic Vac. moulded
--- Ready made
Plastic Inj. moulded
Metal Ready made
Metal Ready made
GRP 1, ready made
Steel wire 1., one Z-bend
Plastic Vac. moulded
Plastic Vac. moulded
GRP 1, ready made
Plastic Decal sheet
Lightweight foam Ready made
Plastic 1 Ø
Plastic 1 Ø
Plastic Vac. moulded
Plastic Oversize
Plastic Oversize
--- Ready made
--- Ready made
Plywood 3, ready made
Plywood 3, ready made
Plywood 3, ready made
Plywood 3, ready made
Plywood 3, ready made
Plastic 1 Ø
Plastic 1 Ø
Metal M 3
--- Ready made
Plastic 3 Ø x 10 Ø x 3
Plastic M 3 x 30
Plastic Ready made
--- Ready made
Plastic 100 long
Plastic Vac. moulded
--- Ready made
Sport Wing
No. off Notes
1
1
1
 each
1
 Not included
 Included with servos





1



 Loop
 Hook
1
 Loop
 Hook
1 Not included
1 Not included

1
1
1
4
4 Loop
4 Hook
1
1
1
1
1 Multi-part
1
1
1
1 Not included
3
Note: we recommend that you apply a coat of sanding sealer to
the wooden parts before fitting them. You may also wish to
colour them to suit the model.
Figs. 1 and 2
- Glue the main spar 1 in the spar / servo lead duct. The angled
ends of the spar must end flush with the underside of the wing ;
this leaves a channel on the top surface for the servo leads.
Ensure that no glue runs into the servo lead channel.
Fig. 3
- Glue the landing skid 3 in the slot.
Fig. 4, overall drawing D
- Cut out the individual decals, working just inside the dotted lines.
- Push pins into the reference points "B1" and "B" to help you
position the decals "D1" and "D". The points "B1" are located
inboard at the change in angle of the gull-wing, on the centreline
of the wing leading edge. The points "B" are located at the tran-
sition between the main wing and the winglet.
See the overall drawing "D".
The decal strips "D5" are not needed until the winglets have been
attached.
Figs. 5 and 6
- Position the large decal "D1" between the two reference points
"B1" and "B", but initially just tack it in place by pressing it onto
the wing leading edge at a few points.
Figs. 7 and 8
- Check that the decal is straight, then cautiously press it onto
both sides of the wing, taking care to avoid trapped air and wrin-
kles.
Fig. 9
- Place the nose fairing 4 over the point of the fuselage, and push
pins into the foam at the corner points to mark its position.
Remove part 4 again.
Figs. 10 and 11
- Position the short inboard decals "D" between the reference
points "B1" and "B3".
No. 3281
3282, 3283