ROBBE Sport Wing 3281 Instrucciones De Montaje página 4

Fig. 12
- Apply the decals "D3" to the top surface of the wing.
Fig. 13
- Set the elevon servos 5 to neutral from the transmitter, cut down
the output arms as shown, and fit them on the output shafts as
a mirror-image pair.
- Fit the swivel pushrod connectors 7 on the underside of the
servo output arms and push the starlock washers 8 over the
pivot shafts to secure them; ensure that the connectors rotate
smoothly. You may need to drill out the linkage hole in the out-
put arms.
- Fit and tighten the servo output screws.
Fig. 14
- Position the servos over their recesses, and deploy the servo
leads in the channels, running them to the wing centre section.
Fig. 15
- Press the servos into the servo wells.
Fig. 16
- Glue the GRP horns 9 in the slots in the elevons.
Fig. 17
- Connect the pre-formed end of the pushrods 10 to the elevon
horns, and slip the plain end through the swivel pushrod con-
nectors mounted on the servos. Tighten the clamping screws in
the swivel connectors.
- Cut off the excess pushrod material; this is only necessary to
prevent them fouling the servo well covers.
- Secure the servos by applying a drop of epoxy to each servo
mounting lug.
- An alternative method of securing the servos is to use thin dou-
ble-sided tape.
Fig. 18
- Place the plastic covers 11 over the servo wells.
Fig. 19
- Cut out the decals "D4" and stick them to the underside of the
wing, flush with both edges of the landing skid. These decals
© robbe Modellsport
Assembly and operating instructions
Sport Wing
also hold the servo well covers in place, and act as hinges if they
need to be opened.
Fig. 20
- Apply a strip of clear adhesive tape over the outside edge of
each servo well cover - see arrows.
Fig. 21
- Glue the recessed hand-grip 1 in place as shown.
- Glue the C.G. indicators 13 in place on both sides at the marked
points.
Fig. 22
This is the procedure for securing the nose fairing 4:
- Place the nose fairing in position and secure it with adhesive tape
- see arrows.
Advantage: if the model crashes, the nose fairing can move
slightly without the paint flaking off, as would happen if the fai-
ring were glued in place.
Fig. 23
- Apply a full-length strip of adhesive tape 14 (decal sheet) to the
elevon and wing, centred over the hinge pivot axis. Press the
tape down firmly.
Fig. 24
- Cut through the elevon along the marked lines at the tip and
inboard ends, cutting as far as the wedge-shaped recess on the
underside. Sand the cut faces smooth.
- Check that both elevons move smoothly up and down.
Fig. 25
- Apply the clear decal strips "D5" to the shoulder of the winglets.
Fig. 26
- Cut out the winglets 15 and sand the cut edges smooth. (Sport
Wings no. 381 and 383 only)
Fig. 27
- Trim the winglets 15 to fit neatly before gluing them to the wing.
You may prefer simply to tape the winglets in place (easier to
replace).
4
Completing the glider version
Fig. 28
- Place the Velcro dots 16 (loop) and 17 (hook) together, and stick the
dots 16 in the circular recesses in the RC compartment as shown.
Fig. 29
- Peel off the backing film from the Velcro dots 17, then place the
RC compartment cover 18 in position.
- Press down on the rear area of the cover in order to stick the
Velcro dots 17 to the inside of the cover 18.
Fig. 30
- Remove the cover again.
- Stick the Velcro patches 19 (loop) in the RC compartment as
shown.
- Stick the mating Velcro patches 0 (hook) to the receiver 1 and
the receiver battery .
Fig. 31
- Place the receiver and the receiver battery in the RC compart-
ment. Connect the servos to the receiver.
- The receiving system is switched on by connecting the receiver
battery to the receiver; a separate switch is not employed on this
model.
- When deploying the receiver aerial be sure to observe the
instructions supplied with your radio control system.
- If you are using a 35 MHz receiver, run the aerial along the under-
side of the wing and deploy it in the long channel.
Fig. 32
- The glider version is completed by fitting the radio compartment
cover; it can now be balanced as described on page 17 and as
shown in Fig. 51.
The power set
Fig. 33
- Separate all the wooden parts from the sheet, and sand the
edges lightly.
No. 3281
3282, 3283