Fitting The Wheels - Peg-Perego GT3 Instrucciones De Uso

EN_English
Thank you for choosing a Peg-Pérego product.
WARNING
_ IMPORTANT: read the instructions carefully before
use and keep them for future reference. The child
may be hurt if you do not follow these instructions.
_ This vehicle was designed for the transport of 1 child
in the seat. Do not exceed the intended number of
passengers
_ This vehicle is designed for children from birth to a
weight of 15 kg.
_ This item was designed for use in combination with
the following Peg Perego Ganciomatic products: the
"Primo Viaggio" car seat (Group 0+) - the "Navetta"
bassinet unit.
_ Before using, make sure the car seat or carrier seat is
correctly fastened.
_ Do not use this item for a number of occupants
greater than that intended by the manufacturer.
_ Be careful not to hurt the child when adjusting the
mechanisms (handlebar, backrest).
_ Always apply the brake when stopped and when
positioning the child in the seat or when removing the
child from the seat.
_ Assembly and preparation of the product, plus
cleaning and maintenance operations, must be
carried out exclusively by adults.
_ Do not use this item if there are parts missing or signs
of breakage.
_ Do not insert fingers into the mechanisms.
_ Any load hanging on the handlebar or the handles
can make the stroller/carriage unstable; follow the
manufacturer's instructions for max load capacity.
_ Do not place loads over 5 kilos in the basket. Do not
place in the bottle holder weights heavier than stated
or hot drinks. Do not place in the hood pockets (if
applicable) weights over 0.2 Kg.
_ The front bar is not designed to support the child's
weight. It is not designed to keep the child in the seat
and does not substitute for the waist belt.
_ Do not use the item near to stairs or steps, heat
sources, naked flames or dangerous objects within
reach of the child.
_ The use of accessories not approved by the
manufacturer could be dangerous.
_ Do not use the rain canopy (if present) indoors and
regularly check to ensure the child is not too warm;
do not park the stroller close to heat sources and keep
well away from lighted cigarettes. Ensure the rain
canopy is not interfering with any moving parts of the
carriage or stroller; always remove the rain canopy
before folding your carriage or stroller.
_ Do not overload the bag. Max. weight allowed is 1 kg.
_ BEFORE USE CHECK THAT THE PEG-
PÉREGO GANCIOMATIC PRODUCTS
ARE CORRECTLY FIXED TO THE ITEM.
_ IT MAY BE DANGEROUS TO LEAVE
YOUR CHILD UNATTENDED.
_ ALWAYS USE THE 5-POINT HARNESS
AND ATTACH THE WAIST STRAP TO
THE LEG DIVIDER STRAP.
_ THIS PRODUCTS IS NOT SUITABLE
FOR JOGGING OR SKATING.
_ BEFORE USE CHECK THAT ALL THE
ATTACHMENT MECHANISMS ARE
CORRECTLY ENGAGED.
- TO AVOID INJURY ENSURE THAT YOUR
CHILD IS KEPT AWAY WHEN UNFOLDING
AND FOLDING THIS PRODUCT.
- DO NOT LET YOUR CHILD PLAY WITH
THIS PRODUCT.
COMPONENTS OF THE ITEM
Check the contents of the packaging and for any
complaints please contact the After-Sales Service.
_ GT3 is composed of: basket; 1 swiveling or locking
front wheel; 2 rear wheels; front bar; cover; hood;
pouch; rain canopy.
_ This product is numbered progressively.
INSTRUCTIONS FOR USE
1 OPENING: unfasten the safety hook before opening
the stroller (fig_a).
Grab the handle with your left hand and use your right
hand to lift the rod all the way up to the last click (fig_b).
2 MOUNTING THE HANDLEBAR: remove the protective
packing caps from the stroller rods (fig_a) and loosen
the two screws and two caps from the handlebar, paying
attention not to lose them (fig_b). Line the handlebar up
with the two rods by pushing it all the way in (fig_c). Pay
attention to the direction of the handlebar: place it as
shown in the figure to avoid fitting it the wrong way.
3 Place the cap and the screw (fig_a) and fasten (fig_b)
on both sides of the handlebar.
4 FASTENING THE BRAKE CABLE: to fasten the brake
cable, slip it into the slot as shown in the figure.
5 FITTING THE WHEELS: To fit the rear wheels, push
them into the slots at the sides until they click into
place (arrow_a). To fit the front wheel, press the
button on the footrest (arrow_b) and push the wheel
on (arrow_c). Check that the wheels are properly
attached by pulling them downwards.
6 BASKET: Press the side buttons (fig_a) and pull the
basket rim off (fig_b), then thread it through the
basket material (fig_c).
7 Push the ends of the basket rim into the slots in the
stroller until they click into place (fig_a). Finally, attach
the basket to the clips at the front (fig_b) and the
sides (fig_c).
8 HOOD: to fit the hood, insert the side fasteners into the
special housings (fig_a), button the hood to the back of the
backrest (fig_b) and to the inside of the armrests (fig_c).
9 Lower the braces to stretch the hood (fig_a).
When you lift the movable part of the hood, you will find
a net insert that provides better ventilation to the baby
(fig_b). To remove the hood, fold the braces, unbutton the
hood, press the side button (fig_c) while slipping the hood
fastener out of its housing (repeat on the other side).
10 COVER: zip the cover to the footrest (fig_a), fasten it
to the side by the Velcro (fig_b) and secure it with the
button (fig_c).
11 FIVE POINT SAFETY HARNESS: To fasten it, push the
two waist strap buckles (with the shoulder straps
attached – arrow_a) into the leg divider until they
click into place (arrow_b). To unfasten it, press the
round button in the centre of the buckle (arrow_c)
and pull the waist straps out (arrow_d).
12 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, do the
opposite. The waist strap can be tightened as far as
the safety lock (fig_b).
13 To adjust the height of the safety harnesses, release
two the buckles on the rear of the backrest; pull
the shoulder straps towards you (arrow_a) until the
buckles are released and insert them in the backrest
loops (arrow_b). Remove the shoulder straps from
- 18 -