Maintenance / Technical Data - Migatronic FLEX 3000 Compact Manual De Instrucciones

Icons for other faults:
The built-in selfprotection system can
also inform the user about other
faults.
The machine should be switched off
and on in order to remove the text.
If the fault code is shown several times, please
contact seller.
Fixed functions
The functions below are fixed and cannot be
connected and disconnected from the display:
Stop of gas flow in case of fault identification
The machine automatically stops the gas flow to the
torch, turns off the welding current in order to let a
possible arc extinguish and stops the wire feeding in
case of a fault.
Automatic stop of re-ignition
Re-ignition is not possible after 5 sec. in case of a
missing arc during ignition.
The arc extinguishes
Welding stops and gas post-flow begins, if the arc
extinguishes during welding. The arc can be re-
established when trigging the torch again.
MAINTENANCE
Lack of maintenance can lead to reduced re-
liability and cancellation of the guarantee.
The FLEX 3000 welding machines require periodical
maintenance. However, the user can carry through
maintenance in the wire room.
Periodical maintenance
In order to prevent problems arising, the follow-
ing procedure should be observed at least once a
year or as required.
- Disconnect the machine from the mains supply
and wait 2 minutes before removing the front
panels. Only trained and qualified staff members
must carry through this procedure.
Clean the fan blades and the components in the
-
cooling pipe with clean, dry, compressed air.
- Drain the cooling liquid out of the cooling module
and welding hoses. Remove dirt and flush with
pure water in the tank and cooling hoses. Fill up
with new cooling liquid. The machine is delivered
with a cooling liquid of type propan-2-ol in the
ratio 23% propan-2-ol and 77% demineralized
water, which provides an anti-freeze solution up to
–9°C.
TECHNICAL DATA
Power source:
Mains voltage
Fuse
No load consumption
Adaptor consumption
Mains current max.
Efficiency
Power factor
Open circuit voltage
100% Permissible duty cycle (40°C ambient temp.)
60% Permissible duty cycle (40°C ambient temp.)
25% Permissible duty cycle (40°C ambient temp.)
100% Permissible duty cycle (20°C ambient temp.)
60% Permissible duty cycle (20°C ambient temp.)
Current range DC
1
Protection class
2
Sphere of application
Norm
Dimension (lxwxh)
Weight (incl. mains cable)
Wire feeding:
Wire feed speed
Torch connection
Dimension wire reel
Separate wire reel
Cooling unit MCU:
Primary voltage
Max. No load consumption
Cooling effiency
Tank capacity
Flow max.
Pressure max.
1
Protection class
Norm
Dimensions
Weight (excl. Cooling liquid)
Function:
Selection of trigger mode
Quattro welding
Pulse welding
Control of current/voltage/wire feed speed
Tach welding
Wire inching
Torch cooling
Current (program specific)
Voltage
Trim
Wire feed speed
Soft-start
Hot-start
Hot-start-time, 2-times
Slope-up
Slope-down
Slope down, time
Stop amp
Pre-flow
Post-flow
Spot time
Arc adjust
Gasflow (option)
Material thickness
Burn back
Sequence
1
Equipment marked IP23 is designed for indoor and outdoor applications
S
2
The machine meets the standards which are demanded of machines
working in areas where there is an increased risk of electric shock
24
FLEX 3000 Compact
400 V ±15%
16 A
40 VA
7.9 kVA
15.5 A
0.85
0.90
15 – 68 V
220 A / 25.0 V
250 A / 26.5 V
300 A / 29.0 V
250 A / 26.5 V
300 A / 29.0 V
15 – 300 A
IP 23
S
EN/IEC60974-1
EN/IEC60974-5
EN/IEC60974-10 (Class A)
69x27x63 cm
32 kg
0,5-24 m/min
EURO
300 mm
no
400 V ±15%
5 W
850 W
4 liter
1.75 l/min–1.2 bar–60°C
2.5 – 3.0 bar
IP 23
EN/IEC60974-2
70x30x22 cm
16 kg
Modes
2-times / 4-times
Quattro off / quattro on
pulse off / pulse on
local / torch control
yes
yes
watercooled / gascooled
15 A – 300 A
0,0 – 68,0 V
±9,9 V
0.5 – 24,0 m/min
0.5m/min – 7m max.
-99 – +100 %
0.0 – 20.0 s
0.1 – 9.9 s
0.0 – 9.9 s
0.0 – 10.0 s
1 – 100 %
0.0 – 10.0 s
0 – 20 s
0.0 – 30 s
-5.0 – +5.0
5 – 27 l/min
program specific
1 – 30
9 sequences