Saving The Remote Controls; On The Built-In Receiver Apricode; On The Optional Receivers, Unico (Memory System) Or Rpl-Eco - Aprimatic SWING 230 APRICODE Instrucciones Para La Instalación Electrica, El Uso Y El Mantenimiento

CONTROL UNIT
3.5

Saving the remote controls

IMPORTANT! The gate must be closed before you can start
saving or cancelling settings.
At the end of programming, check the functioning of the
saved remote controls : button 1 will give the START
command and button 2 will give the PEDESTRIAN START
command (see beside fi gure) - unless otherwise output channel
programming.
3.5.1

On the built-in receiver APRICODE

NOTE:
These instructions are only valid for remote controls in
mode 0.
• Enter the programming menu
radI
• Select the parameter
confi rm the menu "Memories" opens.
• Press the RED button to confi rm
is enabled for 15 sec. (the displays show
• Until the displays show
remote control to be memorised
memo
and the NUMBER of the remote control (
confi rm the remote control has been saved.
! Record the so you can delete this remote control
ADDRESS
as required. Until the displays show
controls can be memorised.
• The programming procedure ends when 15 seconds
elapse without any remote controls is saved.
IMPORTANT NOTE:
To LEAVE programming before the 15 seconds has elapsed,
●
press one of the buttons on the programmed remote control; all
the values confi rmed will be saved.
To DELETE all the programmed remote controls use the
●
parameter (see Programming), confi rm the fi rst time using the
1
RED button .
To DELETE an individual remote control - parameter
●
to the address of the remote control you wish to delete and
confi rm using the RED button
To export all the remote controls saved you require a plug-in
●
memory module (see our catalogue) - parameter
dnLd
; confi rm using the RED button
1
_ before making the change the word
display, if you wish to continue press the RED button again
the display fl ashes for 3 seconds and then the word
displayed (positive conclusion) or the words
codes) are displayed (failure).
3.5.2 On the optional receivers, Unico (Memory
System) or RPL-ECO
WARNING! To use the optional Unico (Memory System) or
RPL-ECO receivers, unplug and remove the built-in receiver
and its antenna (see unit layout diagram).
Plug the UNICO receiver into the connector CN2 or the
●
RPL-ECO receiver into the connector CN1 (see unit layout
diagram).
Connect the antenna and complete the remote control
●
teach programming using the instructions supplied with the
receiver.
(see Par. Programming).
and press the RED button to
Open
the saving time
SEED
).
SEED
, press any button on the
the displays show
ADDRESS
SEED
other remote
r
rn
; scroll
1
.
UPLd
1
.
SURE
is shown on the
donE
Er
+ (see error
SWING APRICODE 230
1 ch1
1
2 ch2
3 ch3
4 ch4
see par. Programming.
fi g. 8 - Saving the built-in receiver APRICODE
Using programming parameters
RED
) this
radI
memo 001
Saving confi rmation: the displays show
NUMBER of the remote control (
tr
. The saving can be quickly enabled using a remote
control already memorised.
and
Remote control
already memorised
is
• Press simultaneously the buttons
control already memorised.
• Press any button on the remote control to be
memorised (until the displays show
memo 001
- 22 -
2 1 2
3 4
RED
open seed
15"
999
÷
memo
).
ADDRESS
seed
15"
Remote controls
to be memorised
1 and 2 on a remote
SEED
999
÷
1
2
15"
and the
15" 5 5 "
15"
).