System Start-Up; Preliminary Checks: Inputs - Movement Direction - Operator Parameters; Self-Teach Movements - Aprimatic SWING 230 APRICODE Instrucciones Para La Instalación Electrica, El Uso Y El Mantenimiento

CONTROL UNIT
3.

SYSTEM START-UP

When the power supply to the unit is switched ON,
the following information is shown on the display: the
FIRMWARE release NUMBER and the name of the system.
When this information is no longer displayed the unit can
be operated.
When the power supply is switched ON to the unit for the
Lrn
fi rst time, fl ashes on the display: preliminary checks
and the self-teach procedure must be performed.
3.1 P reliminary checks: inputs - movement direction
- operator parameters
Make the following checks and settings when
on the display:
INPUT CHECKS
Lrn
During the phase, the fourth display on the card shows
the status of the inputs (fi g.2).
MOVEMENT DIRECTION CHECK (OPEN / CLOSE)
Lrn
During the phase and with the gate is closed, move the
wings using the special button (fi g.3) and check that:
- The FIRST time the YELLOW or BLUE button is pressed
relevant wing is OPENED.
If this does not occur then you must adjust the parameter
d1 d2
and/or
(press the RED button to access programming).
OPERATOR PARAMETERS CHECK
Lrn
During the phase, press the RED button to access
programming (fi g.4) and if necessary modify the
rEL
, parameters in accordance with the type of operator
installed (see the Programming section).
3.2

Self-teach movements

The unit learns the point at which SLOWING STARTS and the
stroke of the movement (STOPPING point).
Lrn
During the phase, press the START controls in sequence
for the self-teach procedure:
START OPENING starts;
START SLOWING starts;
START STOP;
START CLOSING starts;
START SLOWING starts;
START STOP.
If there are two wings then the sequence is wing 1 then
wing 2 OPENING and wing 2 then wing 1 CLOSING (fi g. 6).
!
Warning
External signals are ignored during the self-teach procedure
except for the photocell during closing and STOP signals. If
these signals are triggered the self-teach procedure is stopped
and must be repeated.
IMPORTANT!
The START command to self-teach the STOPPING point
during opening and closing must be given when the wing
reaches the mechanical stop. The additional thrust at the end
of the movement is managed by the parameter (
The self-teach procedure for slowing differs in accordance
with the features of the operator installed:
•
Hydraulic operators without hydraulic slowing and the Electro-
mechanical operators use electronic slowing. The self-teach
procedure identifi es the start points, therefore the START
command must be given when the wing reaches the point
at which you require slowing to start (WARNING:
SWING APRICODE 230
display 4 during
(segment ON = contact closed)
L r N _ -
2 = CLOSING PHOTOCELL
4 = PEDESTRIAN START
5 = SAFETY DEVICE during OPENING
6 = START
Lrn
7 = STOP
fl ashes
During standby, segments 2, 7 and 5 fl ash if the relevant
connections or jumpers are correct.
fi g. 2 -
the
to move the wings press and hold:
• wing1
• wing2
Each time the button is released and then pressed again,
the movement of the relevant wing is reversed.
Mod
and
YELLOW
fi g. 3 -
Access to parameters during
fi g. 4 -
Start the self-teach movements:
L r N _ -
ta t1
- ).
display
during LRn
note: while the display shows
Lrn
and the
button or the STOP control if connected.
rEL
=1).
fi g. 5 -
- 20 -
Lrn
: INPUTS
2
7
6 4
5
lrn
Testing of inputs during
YELLOW button
BLUE button
BLUE
1
MOVES WING
lrn
Special operation during
Lrn
:
RED
LO 0
.
Access to programming during
FA 1
START
(
FA1
the gate can be stopped
phase re-accessed. Simply press the YELLOW
Start of movements during SELF-TEACH
2
MOVES WING
status:
L r N _ -
lrn
)
fi g.7