Important - Beninca HEADY Manual De Instrucciones

The pickup function is enabled or disabled.
On: Enabled pickup. At the beginning of every operation, the motor operates at maximum
SPN
torque for 2 sec.
Off: Disabled pickup.
Select the 1/2 motors operating mode:
On: only one motor (motor 1) active. Function to be used in the following cases:
1mot
- for single motor, to connect M1.
- for two syncronized motors (for instance overhead door), to connect M1 and M2.
Off: Both motors operating.
Enables or disables the programmable code transmitters.
IMPORTANT: The transmitters with programmable code can only be used in conjunction with
the Rolling Code HCS transmitters.
CVAR
On: Radio receiver enabled only for transmitters Rolling Code (ARC or HCS, the first transmitter
sets the operating mode).
Off: Receiver enabled for transmitters Rolling Code HCS and programmable (self-learning and
dip/switch).
The operating mode of the PHOT C input is selected.
On: The PHOT C input is activated in the closing phase only.
In the closing phase: the contact opening causes the motor stop and the immediate rever-
sion of the operation direction (open).
PHTC
Off: PHOT C input is activated in both opening and closing phases.
In the opening phase: the contact opening causes the motor stop. When the photocell is
released, the motor restarts in the opening phase.
In closing phase: the contact opening causes the motor stop. When the photocell is relea-
sed, the motor inverts the movement direction (open).
PP input as OPEN and PED input as CLOSED are enabled or disabled.
OPCL
On: PP input is enabled as OPEN and PED input is enabled as CLOSED.
Off: PP and PED inputs are enabled with their function.
It selects the operating mode of the 2CH/TX output.
On: The output is controlled by the second radio channel of the incorporated receiver. See
2CH
"RADIO" menu to store the transmitter codes.
Off: The output is configurated for the connection of photocells in test mode (see Fig.1).
The thrust function in the closing phase is activated or deactivated by this logic. With SLD
logic only: ON
BB
On: the operation in the closing phase is carried out at normal speed during the last second
(braking is disabled). In this way, a better hooking of the electric lock is performed.
Off: disabled function.
The bistable operation of ELS/SRL output (terminals 12-13) matched to the 2nd radio chan-
nel is enabled or disabled.
SERL
On: bistable operation of the ELS/SRL output activated. The output to terminals 12-13 is
activated/deactivated through the activation of the 2nd radio channel.
OFF: normal operation of the ELS/SRL output based on the TLS parameter.
The remote storage of the radio transmitter codes is enabled or disabled (see par. REMOTE
LEARNING).
REM
On: Enabled remote storage
Off: Disabled remote storage.
MENU
By selecting this function, the receiver is waiting for (Push) a transmitter code to be assigned to the step-by-step function.
Press the transmitter key, which is to be assigned to this function.
PP
If the code is valid, it will be stored in memory and OK will be displayed.
If the code is not valid, the Err message will be displayed.
By selecting this function, the receiver is waiting for (Push) a transmitter code to be assigned to the second radio channel.
Press the transmitter key, which is to be assigned to this function.
2Ch
If the code is valid, it will be stored in memory and OK will be displayed.
If the code is not valid, the Err message will be displayed.
When this function is selected, the receiver awaits (Push) a transmitter code to be assigned to the pedestrian function.
Press the transmitter key, which is to be assigned to this function.
ped
If the code is valid, it will be stored in memory and OK will be displayed.
If the code is not valid, the Err message will be displayed.
By selecting this function, the receiver is waiting for (Push) a transmitter code to be erased from memory.
CLR
If the code is valid, it will be stored in memory and OK will be displayed.
If the code is not valid, the Err message will be displayed.
The memory of the receiver is entirely erased. Confirmation for the operation is asked.
RTR
By selecting this function, the receiver waits for (Push) the GPM key to be pressed again to confirm the operation.
At end of erasing, the OK message is displayed
RESET of the control unit. ATTENTION!: Returns the control unit to the default values.
Pressing the <PG> button for the first time causes blinking of the letters RES, pressing the <PG> button again resets the control unit.
5.3) RADIO (RAD)
5.4) RESET (RES)
FUNZIONE
(ON)
(OFF)
EN
(ON)
(OFF)
(OFF)
(ON)
(OFF)
(OFF)
(ON)
15