Dip-Switches - DITEC E1 Manual De Instalación

2.2 Dip-Switches

Description
DIP1 Control 1-5 function.
DIP2 Direction selection.
DIP3 Restore automatic closing time. - 50%
DIP4 Automation status at power on.
Indicates how the control panel
considers automation when po-
wered up.
2.3 Jumper
Description
SO Reversal safety switch function. With the automation blocked, if the contacts
6→4 Control 1-6 function.
JR3 Incorporated radio receiver.
JR6 Application type.
2.4 Signals
LED
POWER 24 V= power supply.
SA Indicates that at least one of the safety contacts is open.
11 Indicates that the 0-11 limit switch contact is open.
12 Indicates that the 0-12 limit switch contact is open.
SIG Activated during the radio reception phase or transmitter
memorisation.
3. RADIO
The control panel is equipped with a radio receiver with a frequency of 433.92 MHz. The antenna is a 173 mm long rigid wire.
The range of the radio receiver can be increased by connecting the external antenna on the flashing light or by installing a tuned
BIXAL antenna.
Note: use a RG58 (max 10 m) coaxial cable to connect the external antenna to the control panel.
Up to 200 transmitters can be memorised in the BIXMR2 memory.
Attention. If the radio receiver on the control panel is not used, set JR3=OFF and remove the storage module.
Consult the L series remote control use instructions for the memorisation, cloning and cancellation of transmitters.
From one to four CH buttons of the same transmitter can be memorised on the control panel.
If just one transmitter CH button (any) is memorised command 1-5 (step-by-step/open) is performed.
If from two to four CH buttons of the same transmitter are memorised, the operations associated to the CH buttons are as fol-
lows:
- CH1 = command 1-5 step-by-step/open ;
- CH2 = partial opening command, causes the automation to open for 8 s.;
- CH3 = courtesy light on/off command ;
- CH4 = stop command, equal to the 1-9 impulsed command.
If the control panel is replaced, the BIXMR2 memory in use can be introduced to the new control panel.
Attention: the insertion and extraction of the BIXMR2 memory must be carried out in the absence of a power supply.
OFF
Step-by-Step.
Opens towards right.
- Immediate if 6→4=OFF.
Note: the setting of DIP3=OFF and
6→4=OFF is recommended for the imme-
diate reclosing of the barriers.
Open.
If DIP1=OFF, the first command 1-5 activa-
tes the closing.
If DIP1=ON, the first command 1-5 activates
the opening.
Note: with a limit switch installed, preferably
set DIP4=OFF.
OFF
1-8 or 41-8 are open, it is possible to
activate the opening operation.
Note: after the activation of the proximity
limit switch closes the opening of the safety
contact 1-8, 41-8 provokes the STOP during
the closing phase.
Closing.
Disabled.
Sliding gate.
ON
13
Opening.
Opens towards left.
100%
Note: the setting of DIP3=ON is recom-
mended for overhead and sectional doors,
and condominial entrances.
Closed.
The first command 1-5 activates the ope-
ning.
Note: the automatic closing will not be the
first command, even if enabled.
If the automatic closing function is not used,
preferably set DIP4=ON.
With the automation blocked, if the con-
tacts 1-8 or 41-8 are open, any operation
is impossible.
Stop.
Enabled.
Other applications.
Flashing
Indicates the absence of the memory module.
ON
ON
/
/
/
/
E1 - IP1853
GB