Warranty Limitations; Cleaning And Maintenance; Lubrication (Fig. F-4) - Tunturi FitRun 40i Manual Del Usuario

English
Warranty coverage
Under no circumstances shall Tunturi New Fitness BV or the Tunturi
Distributor be liable by virtue of this warranty or otherwise for any
special, indirect, secondary or consequential damages of any nature
arising out of any use or inability to use this equipment.

Warranty limitations

This warranty covers manufacturing defects in the fitness equipment
as originally packed by Tunturi New Fitness BV. The warranty shall
apply only under conditions of normal, recommended use of the
product as described in the Owner's Manual and providing that
Tunturi New Fitness BV's instructions for installation, maintenance and
use have been complied with. Neither Tunturi New Fitness BV's nor
the Tunturi Distributors'
obligations apply to defects due to reasons beyond their control. The
warranty applies only to the original purchaser and is valid only in
countries where Tunturi New Fitness BV has an authorised importer.
The warranty does not extend to fitness equipment or components
that have been modified without the consent of Tunturi New Fitness
BV. Defects resulting from normal wear, misuse, abuse, corrosion, or
damage incurred during loading or transportation are not covered.
The warranty does not cover sounds or noises emitted during use
where these do not substantially impede the use of the equipment
and where they are not caused by a fault in the equipment.
The warranty does not cover defects arising from the failure to
carry periodic maintenance as outlined within the Owner's Manual
for the product. Furthermore, the warranty does not cover defects
arising from usage and storage within an unsuitable environment
as described within the Owner's Manual which should be indoors,
dry, dust and grit free and within a temperature range of +15°C to
+35°C. The warranty does not cover maintenance activities, such as
cleaning, lubricating, and normal part adjustments, nor installation
procedures that customers can accomplish themselves, such as
changing uncomplicated meters, pedals and other similar parts not
requiring any dismantling/reassembling of the fitness equipment.
Warranty repairs carried out by other than authorised Tunturi
representatives are not covered�
Failure to follow the instructions given in the Owner's Manual will
invalidate the product's warranty.

Cleaning and maintenance

⚠ WARNING
• Before cleaning and maintenance, remove the mains plug from
the wall socket.
• Do not use solvents to clean the equipment.
- Do not block the ventilation openings. Keep the ventilation
openings clear from dust, dirt and other obstructions.
- Clean the equipment with a soft, absorbent cloth after each use.
- Clean the visible parts of the equipment with a vacuum cleaner
with a small suction nozzle
- Regularly check that all screws and nuts are tight.
Belt and Running Deck
Your treadmill uses a very high-efficient low-friction bed. Performance
is maximized when the running deck is kept as clean as possible.
Use a soft, damp cloth or paper towel to wipe the edge of the belt
and the area between the belt edge and frame. Also reach as far
as practical directly under the belt edge. This should be done once
a month to extend belt and running deck life. Use water only - no
cleaners or abrasives. A mild soap and water solution along with a
nylon scrub brush will clean the top of the textured belt. Allow the
belt to dry before using.

Lubrication (fig. F-4)

The running belt must be checked for lubrication condition regularly.
Therefore the treadmill comes with a 300 hours reminder function.
The "TIME WINDOW" will display "OIL" and will make an acoustic
beeping sound every 10 seconds to remind you. Follow the below
checking procedure and eliminate the "OIL" message and acoustic
warning signal by pressing and hold the "STOP" button for at least 3
seconds during this warning signal.
⚠ WARNING
• Before lubrication, remove the mains plug from the wall socket.
⚠ CAUTION
• We recommend to check the running belt lubrication at least
once every month, as more factors than time can be effective to
the lubricant conditions.
• Only lubricate the running belt if necessary. If you apply too
much lubricant, the running belt will slip easily due to lack of
friction�
- Stand steadily on the running belt.
- Take hold of the front handlebar and push the running belt with
your feet so that it slides back and forth. The running belt must
move smoothly and evenly without making sound.
- If the running belt does not move smoothly and evenly or if the
running belt does not move at all, touch the underside of the
running belt with your fingertips to check the lubrication:
• If you feel lubrication or your fingertips are shiny, there is
sufficient lubrication on the running belt.
• If you do not feel lubrication or your fingertips are dusty or
rough, apply lubricant (15-20 ml) in the middle of the running
deck under the running belt and let the equipment operate at
5km/h for at least 5 minutes.
• After lubrication, do not fold the equipment before having done
a workout for 20 minutes with a speed of at least 5 km/h. The
lubricant will be spread evenly over the running belt.
Belt Dust
This occurs during normal break-in or until the belt stabilizes. Wiping
excess off with a damp cloth will minimize build-up.
General Cleaning
Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent buildup. Twice a year, you should remove the black motor
hood and vacuum out dirt that may accumulate.
UNPLUG POWER CORD BEFORE THIS TASK.
Belt adjustments
Adjustment must be made from the rear roller. The adjustment bolts
are located at the end of the step rails in the end caps.
- Tighten the rear roller bolts (clockwise) only enough to prevent
slippage at the front roller. Turn both running belt tension
2 0