GreenWorks Tools RLT5030S 23lgs Manual De Usuario página 11

EN
DE
FR DE ES IT
FR EN ES IT PT
Deutsch(Übersetzung der originalen Anleitungen)
Keep visitors away from the worksite. All visitor and
■
onlookers, especially children and infirm person
should be kept well away from where you are
working. Do not let others in the vicinity make contact
with the tool or extension cord.
Store tools safely. When not in use tools should be
■
stored in a dry place and locked up out of the reach of
children.
Do not force the tool. The tool will do the job better
■
and more safely working at the rate for which it was
designed.
Use the correct tool for the job. Do not force small
■
tools or attachments to do the job best handled by a
heavy duty tool. Never use a tool for a purpose other
than that for which it was intended.
Dress correctly. Do not wear loose clothing
■
or jewellery; they can get caught in moving
parts. Rubber gloves and non-slip footwear are
recommended when working outdoors. If you have
long hair wear a protective hair covering
Use safety accessories. Safety glasses and ear
■
protectors should always be worn. A face or dust
mask is also required.
Do not abuse the power cord. Never pull the cord to
■
disconnect the tool from the power point. Keep the
cord away from heat, oil and sharp edges.
Look after your tools. Keep tools clean for better
■
and safer performance and follow the instructions
regarding lubrication and accessory changes. Inspect
extension cords periodically and replace them if
damaged. Keep tool handles dry, clean and free from
oil and grease.
Disable idle tools. Switch off the power and
■
disconnect the plug from the power before servicing,
when changing accessories and when the tool is not
in use.
Avoid unintentional starting. Always check that the
■
switch is in the OFF position before plugging in the
tool to the power supply. Do not carry a plugged in
tool with your finger on the switch.
Use outdoor rated extension cords. When a tool is
■
used, use only extension cords that are intended for
outdoor use and are so marked. It is advised to use
an RCD when using an extension cord outside.
Stay alert. Watch what you are doing. Use common
■
sense. Do not operate a power tool when you are
tired.
Check for damaged parts. Before using a tool,
■
check that there are no damaged parts. If a part is
slightly damaged, carefully determine if it will operate
properly and perform its intended function. Check
for alignment of moving parts, binding of moving
parts, breakage of part's proper mounting and any
other conditions that may affect the operation of the
tool. A guard or other part that is damaged should
be properly repaired or replaced by an authorized
RLT5030S 23lgs manual.indd 9
PT NL SV DA NO FI HU CS RU
NL SV DA NO FI HU CS RU
English(original instructions)
9 9
RO PL SL HR ET
RO PL SL HR ET
service facility unless otherwise indicated in this
Instruction Manual. Defective switches must be
replaced by an authorized service facility. Do not use
a tool if the switch does not turn the tool on and off
correctly.
Guard against electric shock. Prevent body contact
■
with 'grounded' objects such as water pipes,
radiators, cookers and refrigerator enclosures.
Use only approved parts. When servicing use only
■
identical replacement parts. Use an authorized
service facility to fit replacement parts.
Be aware of the harmful/toxic dusts arising from
■
grass trimming etc, (e.g. fertilizers, insecticides).
The use of improper accessories or attachments
■
other than recommended can lead to personal injury.
This electric tool is constructed in accordance with
■
the relevant safety requirements. Only experts may
repair the electric tool. Otherwise, it may endanger
your life.
Voltage — make sure power supply is correct for your
■
machine. The voltage of this machine is on the rating
plate.
IMPORTANT: additional safety notes for your Grass
Trimmer.
During assembly take great care when fitting the
■
guard as this has a very sharp cutting edge on one
side for cutting the nylon line.
Never hold the cutter head above foot height or point
■
it towards people or animals when in use.
If the trimmer starts to vibrate excessively switch
■
off immediately and have it checked by a qualified
service engineer.
CAUTION: The cutting head continues to rotate
for a few seconds after switching off.
Always remove any sticks and stones etc. before
■
using the trimmer.
Keep hands and feet away from the cutting means at
■
all times and especially when switching on the motor.
Do not cross roads or gravel paths while operating
■
trimmer.
On steep slopes cut across the slope, never in an
■
up and down direction. Never run while using the
trimmer.
Never fit a metal replacement line.
■
Never use the trimmer while it is raining or in damp
■
weather.
Use the trimmer in daylight or good artificial light.
■
Never use when visibility is bad.
Do not overreach, keep proper footing and balance at
■
all times.
Take care against injury from any device fitted for
■
trimming the filament line length. After extending new
cutter line always return the machine to its normal
operating position before switching on.
LT LV SK BG
LT LV SK BG