Makita 0DVC261 Manual De Instrucciones página 13

Connecting the tool
NOTE: If the bent pipe assembly is attached to the
hose, remove it beforehand.
T o c onne c t a tool to t h e c leaner, t h e d e d i c ate d h ose an d / or a d d i-
tional parts are re q uire d . D epen d ing on y our c leaner mo d el, y ou
nee d to repla c e t h e h ose an d / or prepare a d d itional parts.
R e f er to t h e f ollo w ing table f or d etails.
Supplied Hose end type
hose
diameter
ø 28 mm
w ith out part
w ith snap-on part
ø 32 mm
w ith snap-on part
ø 38 mm
w ith snap-on part
w ith f ront c uf f 38
NOTE: A lw ay s use a suitable f ront c uf f . W h en using th e f ront
c uf f 24 , attac h it to th e f ront c uf f 22 th at is c onnec ted to th e h ose.
Fig.20: 1. F ront c u f f 22 2. F ront c u f f 2 4
W hen using ø2 8 mm dust extraction hose
1. A tta c h t h e f ront c u f f to t h e h ose f or d ust e x tra c tion.
W h en c onne c ting t h e f ront c u f f , make sure t h at it is
se c urel y s c re w e d on t h e h ose.
2. C onne c t t h e f ront c u f f to t h e tool ' s e x tra c tion outlet.
Fig.21: 1. F ront c u f f 2. E x tra c tion outlet 3. H ose
T h e f ront c u f f c an be d eta c h e d b y turning it c ounter-
c lo c k w ise w h ile h ol d ing t h e h ose.
Action
A ttac h th e f ront c uf f .
R eplac e th e h ose end
( snap-on part) w ith th e f ront
c uf f .
T h e h ose end c an be remov ed
by turning it c ounterc loc kw ise.
R eplac e th e h ose w ith th e one
f or d ust ex trac tion ( ø 28 mm,
w ith f ront c uf f ) .
R eplac e th e h ose w ith th e one
f or d ust ex trac tion ( ø 28 mm,
w ith f ront c uf f ) .
Attach the joint - or the
f ront c uf f 24 .
W hen using ø3 8 mm hose with front cuff 3 8
Twist and insert the joint or the front cuff to the
1.
inlet part on t h e h ose, d epen d ing on t h e tool t h at y ou
are going to c onne c t.
2. C onne c t t h e f ront c u f f to t h e tool ' s e x tra c tion outlet.
Fig.22: 1. Joint 2. F ront c u f f 3. E x tra c tion outlet
4. H ose
To remove the joint and the front cuff, follow the installa-
tion pro c e d ures in re v erse.
Attaching bent pipe assembly
Optional accessory
NOTE: Y ou d on ' t nee d to per f orm t h is pro c e d ure
i f y our mo d el c omes w it h t h e bent pipe assembl y
atta c h e d to t h e h ose.
NOTE: T h ere are t w o t y pes o f bent pipe assembl y ;
t h e one f or sli d e-t y pe e x tension w an d an d t h e one f or
ring-t y pe e x tension w an d . I f y ou prepare t h e bent pipe
assembl y , c h oose t h e one f or y our d esire d e x tension
w an d t y pe.
T h e bent pipe assembl y is use d f or c onne c ting t h e e x ten-
sion w an d or no z z le f or v a c uum c leaning to t h is pro d u c t.
I f y ou w ant to use t h is pro d u c t as t h e v a c uum c leaner,
atta c h t h e bent pipe assembl y to t h e h ose.
T o atta c h , uns c re w t h e f ront c u f f f rom t h e h ose an d
f asten t h e slee v e o f bent pipe assembl y onto t h e h ose.
T o remo v e, loosen t h e slee v e o f bent pipe assembl y
f rom t h e h ose.
Fig.23: 1. H ose 2. Bent pipe assembl y 3. S lee v e
Installing filter bag / dust bag
Optional accessory
Do not use a damaged filter bag.
CAUTION:
Always use the vacuum cleaner with the filter bag
properly installed. Otherwise the vacuumed dust or
particles may be exhausted from the cleaner and
they may cause respiratory disease to the operator.
When the filter bag is already full, replace
NOTICE:
w it h ne w one. W h en t h e d ust bag is alrea d y f ull,
empty it. Continuous use with the filter bag/dust bag
f ull results in re d u c e d su c tion po w er.
1. U nlo c k t h e lat c h b y li f ting t h e bottom si d e. P us h
t h e groo v e d area to li f t t h e f ront lat c h ing si d e. P ull t h e
lat c h to open t h e li d .
Fig.24: 1. H ook 2. L i d
Insert the filter bag into the slit on the upper side of
2.
t h e room as illustrate d .
Fig.25: 1. S lit 2. F ilter bag
W h en using t h e d ust bag, insert t h e brim o f t h e d ust bag
into t h e slit.
Fig.26: 1. S lit 2. Brim 3. D ust bag
Align the hole of the filter bag with the hose cuff and
3.
pus h t h e c ar d boar d portion to t h e en d . Make sure t h at t h e
rubber ring on the filter bag goes over the rim on the hose cuff.
Fig.27: 1. Rubber ring on the filter bag 2. R im on
t h e h ose c u f f 3. C ar d boar d portion o f t h e
filter bag 4. H ose c u f f
13 ENGLISH