Tool Specifications; Fastener Specifications; Operating Pressure; Air Consumption - Bostitch TU-216 Serie Manual De Operación Y De Mantenimiento

TOOL SPECIFICATIONS

All screws and nuts are metric
MODEL LENGTH
TU-216-71 8.71" (221.25 mm)
TU-216-71LN 8.71" (221.25 mm)
TU-216-71LM 13.925" (353.69 mm)
TU-216-71A 8.71" (221.25 mm)
TU-216-71ALM 13.925" (353.69 mm)
TU-216-80 8.71" (221.25 mm)
TU-216-80LN 8.71" (221.25 mm)
TU-216-80LM 13.925" (353.69 mm)
TU-216-80ALM 13.925" (353.69 mm)
TU-216-84 8.71" (221.25 mm)
TU-216-97 8.71" (221.25 mm)
TU-216-SJK 8.71" (221.25 mm)

FASTENER SPECIFICATIONS

TOOL MODEL STAPLE SERIES
TU-216-71 BA71
TU-216-71LN BA71
TU-216-71LM BA71
TU-216-71A BA71
TU-216-71ALM BA71
TU-216-80 BA80
TU-216-80LN BA80
TU-216-80LM BA80
TU-216-80ALM BA80
TU-216-84 SBNK, ATRO 84
TU-216-97 BA97
TU-216-SJK ATRO SJK
TOOL AIR FITTING
This tool uses a free-flow connector plug, 1/4 N.P.T. The inside diameter should be .200"
(5mm) or larger. The fitting must be capable of discharging tool air pressure when
disconnected from the air supply.

OPERATING PRESSURE

70 to 100 p.s.i.g. (4.8 to 6.9 bar). Select the operating pressure within this range for best
fastener performance.
DO NOT EXCEED THE RECOMMENDED OPERATING PRESSURE.

AIR CONSUMPTION

The TU-216 requires 1.71 cubic feet per minute (.048 cubic meters) and the TU-216-LN
models require 1.84 cubic feet per minute (.052 cubic meters) of free air to operate at the
rate of 100 nails per minute, at 80 p.s.i. (5.5 bar). Take the actual rate at which the tool
will be run to determine the amount of air required. For instance, if your fastener usage
averages 50 nails per minute, you need 50% of the tool's c.f.m. which is required to
operate the tool at 100 nails per minute.
HEIGHT
5.92" (150.26 mm)
7.81" (198.30 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
7.81" (198.30 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
5.92" (150.26 mm)
CROWN WIDTH WIRE SIZE
3/8" (9.0 mm) .023X.030(.58mmX.75mm)
3/8" (9.0 mm) .023X.030(.58mmX.75mm)
3/8" (9.0 mm) .023X.030(.58mmX.75mm)
3/8" (9.0 mm) .023X.030(.58mmX.75mm)
3/8" (9.0 mm) .023X.030(.58mmX.75mm)
1/2" (13mm) .027X.036(.69mmX.91mm)
1/2" (13mm) .027X.036(.69mmX.91mm)
1/2" (13mm) .027X.036(.69mmX.91mm)
1/2" (13mm) .027X.036(.69mmX.91mm)
31/64"(12.3mm) .023X.040(.55mmX1mm)
3/16"(4.8mm) .027X.036(.69mmX.91mm)
5/32"(4.1mm) .024X.029(.60mmX.70mm)
-4-
WIDTH WEIGHT
1.58" (40.2 mm) 1.88 lb (.853 kg)
1.58" (40.2 mm) 2.01 lb (.912 kg)
1.58" (40.2 mm) 2.34 lb (1.061 kg)
1.58" (40.2 mm) 1.91 lb (.867 kg)
1.58" (40.2 mm) 2.37 lb (1.075 kg)
1.58" (40.2 mm) 1.82 lb (.807 kg)
1.58" (40.2 mm) 1.97 lb (.894 kg)
1.58" (40.2 mm) 2.23 lb (1.012 kg)
1.58" (40.2 mm) 2.26 lb (1.025 kg)
1.58" (40.2 mm) 1.82 lb (.826 kg)
1.58" (40.2 mm) 1.79 lb (.813 kg)
1.58" (40.2 mm) 1.79 lb (.813 kg)
FASTENER RANGE
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)
5/32'-5/8"(4mm-16mm)
5/32"-5/8"(4mm-16mm)