Package Includes - Franklin Electric INLINE CONSTANT PRESSURE SYSTEM El Manual Del Propietario

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

NOTICE indicates special instructions which are important but

not related to hazards.

Carefully read and follow all safety instructions in this manual

and on pump.

HAZARDOUS PRESSURE:

WA R N I N G

Pump should not be operating

when water is not in use. Do

not run pump against closed

discharge. Release all system

pressure before working on

any component.

C A U T I O N Do not run pump dry. Fill pump with water

before starting or pump will be damaged.

This Inline Constant Pressure System is guaranteed by the

manufacturer. In the event of a product failure, it must be

returned to an authorized water system professional for

repairs. Warranty is void if repairs are not made by an

authorized technician

ELECTRICAL SAFETY

C A U T I O N

Make sure all ELECTRICAL POWER IS

OFF before connecting any electrical wires.

W A R N I N G

Hazardous voltage.

Can shock, burn, or

cause death.

Ground pump before

connecting to power

supply. Disconnect

power before working

on pump, motor or

tank.

C A U T I O N

DO NOT touch an operating Inline

System. The surface of either the drive or pump unit

may be HOT. Allow all system components to cool

for thirty (30) minutes before handling.

Suitable for use on a circuit capable of delivering

not more than 5000 RMS symmetric amperes, 260

volt maximum.

The output connector on the drive is only

intended for use with the motor specified in the

Replacement Parts section of this manual.

Integral solid state short circuit protection does

not provide branch circuit protection. Branch circuit

protection must be provided in accordance with the

National Electric Code or Canadian Electric Code

and local codes.

Wire Inline System for

correct voltage. See

"Electrical Installation"

section of this manual and

Inline System nameplate.

Connect power supply

ground to ground terminal

in wiring compartment

before connecting power

supply.

Meet National Electrical

Code (NEC) or Canadian

Electrical Code (CEC) and

local codes for all wiring.

Follow all pump wiring

instructions provided in this

manual.

GENERAL SAFETY

The Franklin Electric Inline System is designed and built with

a NEMA 4 approved drive enclosure to protect the pump's

electronic components.

INLINE SYSTEm KEY FEATURES

SYSTEm FEATURES:

• Constant water pressure with a wide range of

settings. (10-80 psi, 0.7 - 5.5 bar)

• Pump speed is controlled to provide the optimum

performance without overloading the motor

• Product Power Rating: 1.2 hp (0.9 kW)

• Low current motor start-up (soft-starting)

• Quiet operation

• Single pump/motor/drive controller design

• Compact footprint, 19 in x 8 in (480 mm x 200 mm)

• Shipping weight: 50 lbs (22.7 kg)

PUmP FEATURES:

• Operates on a wide range of flows from flooded

suction to 35 gpm (135 lpm)

• Requires minimum incoming pressure of 3 psi

(0.2 bar) Exception: Cisterns may be flooded suction

without vortexing

• Increases incoming pressure by up to 60 psi (4.1 bar)

• Stainless steel construction for all wetted surfaces

DRIvE CONTROLLER PROTECTION FEATURES:

• No in-rush (power-on transient) current

• Over pressure shut off optional

(See Replacement Parts Section)

• Low water shut off

• Locked pump detection/shut off

• Water over-temperature shut off

• High voltage/lightning surge protection

• Low line voltage protection

• Motor under and overload protection

• Open and short circuit protection

• NEMA 4 enclosure

INSPECT YOUR SHIPmENT

All Franklin Electric Inline Systems are carefully tested, inspected,

and packaged to ensure their arrival in perfect condition. When

the pump is received, examine it closely to make sure there is

no damage that may have occurred in shipping. If damage is

evident, report this immediately to your shipping carrier and

product dealer. The shipping carrier assumes full responsibility

for the shipment's safe arrival. Any claim for damage to the

shipment, either visible or concealed, must be made through the

shipping carrier first.