Memorisation Of Transmitter Mod. Mt4; Programming Keypad Mod. Mk - moovo XW4 Instrucciones Y Advertencias Para La Instalación Y El Uso

9.2 – MEMORISATION OF TRANSMITTER mod. MT4
CAUTION! - Always read the procedure first and then perform the
operations in the correct sequence without allowing more than 10 sec-
onds to pass between releasing one key and pressing the next.
To enable control of the automation with the transmitter, the keys must be
memorised in the control unit memory.
Memorisation enables the association of each key with the required com-
mand, selecting from the following:
1 = Step-Step: Corresponding to the sequence ... Open - Stop - Close
- Stop ... The first command activates Opening; the next, with the leaf
moving, activates Stop; the third activates Closure; the fourth with the leaf
moving activates Stop and so on.
2 = Step-Open: Corresponding to the sequence ... Open - Stop -
Close - Open ... The first command activates Opening; the next, with the
leaf moving, activates Stop; the third activates Closure; the fourth with the
leaf moving activates Open and so on.
3 = Partial open: Corresponding to total opening of one leaf only This
command is only activated if Leaf 2, the subordinate leaf, is completely
closed.
4 = Apartment block open: This command is used for apartment
blocks and envisages programming of all apartment block transmitters
with a single "apartment block opening" key. This command operates as
follows:
• if the command is sent while an Opening manoeuvre is in progress, the
manoeuvre continues;
• if the command is sent while a Closing manoeuvre is in progress, the
manoeuvre is interrupted and an Opening manoeuvre is started;
• if the command is sent when the gate is stationary and completely open,
the Closing manoeuvre is started. Note – Automatic closure of the gate is
also possible, by programming a pause time as required (see chapter 10).
A single procedure memorises a single key of the transmitter; this can be
memorised both on the present control unit and on control units of other
automations. The control unit memory can memorise up to 150 keys.
For each key to be memorised, repeat the following procedure.
01. Select which transmitter key is to be memorised (for example: Key
T3).
02. Decide on the command (from those listed below) to be associated
with the selected key (for example: Command "2").
03. Press "P1" (on the Control unit) the same number of times as the
selected command number (in the example "2", i.e. twice) and check
that the green led emits the same number of quick flashes (repeated
at regular intervals).
04. (within 10 seconds) Press and hold the transmitter key to be memo-
rised for at least 2 seconds (in the example, key T3).
If the memorisation procedure is successful, the green led emits 3 long
flashes (= memorisation OK). Note – Before the 10 second interval elaps-
es, the key of a NEW transmitter with the same command can be mem-
orised (useful, for example, when several transmitters need to be memo-
rised on the same control unit).
Otherwise wait until the green led turns off (= procedure completed) and
for the red led to resume flashing at regular intervals.
9.3 – PROGRAMMING KEYPAD mod. MK
The control keypad can be programmed for two alternative operating
modes:
- TRADITIONAL mode (without the use of a personal password)
- SAFETY mode (with use of a personal password)
After memorisation (see STEP 9.1) the keypad is set to "Traditional mode"
(factory setting) but this may be modified as described below.
"Traditional" operating mode"
In this mode the keys are independent and each commands a specific
action. The commands are:
Key "A" = Step-step command
Key "B" = Partial open command
Key "C" = Open Command
Key "D" = Close command
Key "OK" = Stop Command
"Safety" operating mode"
In this mode the keypad is enabled on entry of a password set by the user
(from 1 to 10 letters) followed by the key OK. This combination of keys
only sends the specific command that the user set during the mode pro-
gramming phase.
Note – If the Step-Step command is programmed, after the command is
sent the user has 10 seconds in which to send a subsequent command,
by simply pressing "OK". This eliminates the need to repeat password
entry.
"SAFETY" MODE PROGRAMMING
01. Press and hold keys "A" and "B" simultaneously for a few seconds,
until the keypad emits a sequence of beeps that indicate start-up of
programming.
02. Using the keys enter the "PUK code" (10-letter code supplied with the
keypad); and then press "OK".
If the code is correct the keypad emits a series of beeps; if incorrect
a single continuous tone is emitted.
03. Using the keys enter the personal password (from 1 to 10-letters);
and then press "OK".
The keypad emits a series of beeps.
04. From the list below, select the command to be programmed and on
the keypad press the key to be associated with the command fol-
lowed by OK.
Step-Step command
"Partial open" command
Open command
Close command
Stop command
The keypad emits a series of beeps to indicate completion of pro-
gramming.
Modifying the Personal Password
To modify you personal password, repeat the entire "Safety mode" pro-
cedure, changing the existing password at point 03.
"TRADITIONAL" MODE PROGRAMMING
To program this mode, perform the "Safety mode programming" proce-
dure, and at point 03 and 04 press "OK" only.
= key A
= key B
= key C
= key D
= key OK
English – 23