EdilKamin INPELLET 49 Instalación Uso Y Mantenimiento página 34

The wording "S E " will appear for con rmation with " ". This will allow you to chec that the operations performed are
correct, prior to completion (the wording "S
eekly timer
Press and hold the " " ey on the remote control for seconds. This turns on the cloc regulation and by pressing the
ey, the wee ly timer function is accessed, with the display showing the description "PRO R
This function allows you to set a number of times the insert turns on and off per day (up to a ma imum of three), each
day of the wee .
s you con rm the display with the ey " ", one of the following options will appear:
NO PRO . (no programme set)
D IL PRO R (single programme for every day of the wee )
EE L PRO R . (speci c programme for each day individually)
se the " " and " " eys to switch between programmes.
se ey " " to con rm the option "D IL PRO R
day.
se the "D IL PRO R
By then pressing the " " ey, the following can be seen:
- Prog. no.
- 1st prog. (one turn on and one turn off per day), nd prog. (identical), rd prog. (identical)
se the " " ey to show in reverse order.
If the 1st programme is selected, the turn on time is shown.
The display shows: 1 "ON" at 1
The display shows: 1 "ON" at
The same applies for the turn-off time to be set and for subsequent turning on and off.
on rm by pressing " " and the wording "S
hen con rming " EE L PRO R
1 on ; Tues; ed; 4 Thurs; Fri; Sa; Sat
Once you have chosen the day, use the " " and " " ey and con rm with the " " ey, to programme in the same way as for the
"D IL PRO R ", choosing whether or not to enable a programme for each day of the wee , and if so
choosing number of interventions and at what times.
Should you ma e an error during programming, you can leave the programme without saving. s you press a ey,
splay will show the word "no S
Changing pellet loading
Press the " " button for two seconds from the radio control and scroll the display instructions with the " " and "-" buttons. ou
will come across the message " ser menu" and when you con rm, the message " D -PELLET and D -DR
If we set " uto-ad ust. ON", the system will automatically ad ust pellet dropping. lternatively, if we set " uto-ad ust. OFF," we
can manually correct pellet dropping, varying the range in terms of percentages ( /-
By con rming this function with the menu ey, you can access the function to ad ust pellet loading. By decreasing the
value set, pellet loading is decreased. By increasing the value set, pellet loading increases. This function is useful if
changing the pellet type for which the insert has been calibrated and loading therefore needs correcting.
Should this correction not suf ce, contact the Edil amin-authorised Dealer, to establish the new operating a is.
Notes on ame variability
Flame status may vary depending on the type of pellet used, in addition to normal solid fuel ame variability and regular combu-
stion chamber cleaning carried out automatically by the boiler.
(N.B.: which does NOT replace necessary cold suction by the user prior to ignition).
RESERVE ARNING
The INPELLET 49 is tted with an electronic function that detects the residual quantity of pellets in the tan .
The detection system is integrated into the electronic board, allowing you to see how many hours and g are left until
pellet e haustion, at all times. For correct system function, it is important that the following procedure is followed during the rst
ignition (by the Dealer).
INSTRUCTIONS FOR USE
E" will then be shown on the display).
" to choose the number of programmes (turn on/off) to be carried out per
" to set identical programme/s for every day of the wee .
se the " " and " " ey to change the hour. on rm with the " " ey.
se the " " and " " ey to change the minutes. on rm with the " " ey.
E " will appear on the display.y.
", you will need to choose the day to which the programming is to apply:
E".
%).
- 34
-
ON/OFF".
, he di-
T" will appear.