Possible Troubleshooting - EdilKamin FANTASY Instalación Uso Y Mantenimiento

POSSIBLE TROUBLESHOOTING

In the event of proble s the stove stops auto atically and runs the shutdown process and the display shows text
regarding the otivation of the shutdown (see the various alar s below).
Never pull the plug during shutdown on account of
Should it bloc to restart the stove you will need to allow the turn-off procedure to ta e place (6
audible signal) and then press the button 1 .
o not turn the stove on again before chec ing the cause of the
IN ICATION OF POSSIBLE CAUSES OF MALFUNCTION AN IN ICATIONS AN REME IES:
1) Signalling: eri c. air ow: (intervenes if the ow sensor detects insuf cient combustion ).
Proble : Turns off for lac of depression
ir ow may be insuf cient because the door is open, the door does not close properly (e.g. bad seal), there is an
air inta e or smo e e traction problem, or the combustion chamber is clogged.
Actions:
hec :
door closure;
combustion air inta e duct (clean, paying attention to the ow sensor components);
clean the ow sensor with dry air (li e that used for
stove location: it must not be installed against a wall;
combustion chamber position and cleanliness (clean regularly according to the type of pellet);
smo e duct (clean);
installation (if it does not comply with regulations or the smo e outlet has more than - bends);
f you suspect the sensor is malfunctioning, carry out cold tests. f the conditions are changed (for e ample by
opening the door) and the value does not change, there is a sensor problem.
N.B.:
he no depression alarm may also occur during ignition, since the ow sensor starts monitoring 9 seconds after
the ignition cycle begins.
2) Signalling: eri c. extract.: (this trips if the smo e e traction speed sensor detects a fault)
Proble : Shutdown for s o e extraction speed fault detection
Actions: hec smo e e tractor function (devolution sensor connection) and board ( E LER).
hec smo e channel for dirt
erify the electrical system and earthing system.
hec eletronic circuit board ( E LER).
) Signalling: Stop Fla e: (this trips if the thermocouple detects a smo e temperature lower than the value set, which it
interprets as the absence of ames)
Proble : urns off due to drop in smo e temperature
Actions:
lac of pellets
too many pellets have suffocated the ame, chec pellet quality ( E LER)
the ma imum thermostat has intervened (rare, this only intervenes in the event of e cessive smo e
temperature) ( E LER)
) Signalling: Bloc FI NO Start: (intervenes if a ame fails to appear within a ma imum of
temperature is not reached).
Proble : Turns off due to incorrect s o e te perature during ignition
istinguish either of the following cases:
Fla e does NOT appear
Actions:
hec : - combustion chamber position and cleanliness;
arrival of combustion air in the combustion chamber;
if the heating element is wor ing ( E LER);
room temperature (if lower than
ry to light with a relighter (see page
Fla es appear but AF appears on the display after Ar
Actions: hec : (only by the ealer)
if the thermocouple is wor ing ( E LER);
start-up temperature setting in the parameters ( E LER).
Repeat start up after having emptying the brazier.
) Signalling: Blac Out: (not a defect of the stove).
Proble : Turns off due to lac of electricity
Actions: hec electricity connection and drops in voltage.
6) Signalling: Fault RC: (intervenes if the thermo coupling has failed or is disconnected).
Proble : Turns off due to ther o coupling failed or disconnected
Actions:
hec connection of thermo coupling to board: chec function in cold test ( E LER).
alfunction.
alfunction and CLEANING EMPTYING the crucible.
eyboards);
use a relighter) and damp.
).
- 45
-
seconds with
minutes, or if ignition