Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
www.groupdynamics-laundry.com
sales@groupdynamics.lv
Press "ENTER" to change the selection.
Use the "UP" and "DOWN" keys to set the
delay in minutes and/or hours and then press
"ENTER" to confirm.
Press "MODE" to exit.
Changing heating temperature
Heating: The maximum wash bath
temperature reached through heating in any
cycle can be lowered by 10°C. Select
"HEATING" using the "UP" and "DOWN"
keys.
Press "ENTER" to confirm.
The parameter status, i.e. either "NORMAL"
or "REDUCED" will appear. Press
"ENTER" to change the selection. Use the
"UP" and "DOWN" keys to make your
selection and then press "ENTER" to
confirm.
Press "MODE" to exit.
Enabling cycles
Enable: When one or more cycles are not
desired, it is possible to hide them from the
available alternatives. This means that they
are not erased but only concealed from the
user interface menu that is accessed by the
"SELECT" and "UP" or "DOWN" keys.
Select "ENABLE" using the "UP" and
"DOWN" keys.
Press "ENTER" to confirm.
Using the "UP" and "DOWN" keys it will
be possible to scroll all programs and their
enable/disable settings. Move to the desired
cycle and press "ENTER". Again using the
"UP" and "DOWN" keys, choose between
"ENABLED" and "DISABLED" and press
"ENTER" to confirm.
Press "MODE" to exit.
7.4 USEFUL ADVICE
Remember that loading 80% of the machine's
rated capacity provides better wash results.
Mind that more soap does not mean better
wash: on the contrary, using too much
washing powder leads only to unnecessary
pollution. The right amount of soap is
indicated by your supplier according to the
relevant water hardness.
Unless specifically advised against, the use
of the water economiser is warmly
recommended and so is the reduction of
maximum temperature, in order to curb water
and energy consumption and consequently
reduce cycle length.
Before filling the drum with laundry make
sure that keys, zips, clasps and buckles are
facing inside and pockets are empty.
At the end of the job do the following:
- leave the door open;
- turn the machine off by the main switch
- close the hot water, cold water and steam
taps (the latter applies to steam-heated
machines only).
- turn the wall cutoff switch off.
7.5 WASH PROGRAMS
Cycle steps are detailed in the user-friendly
tables attached.
7.6 WARNING
- Do not leave the machine on to no purpose.
TURN the main switch OFF when the
machine is not used.
During use:
- Open the door only when the drum is still
and drained.
- In case of a potential drop, open the door by
the manual puller, down on the left.
Before opening the door make sure that the
drum has come to a complete halt, that the
water has been drained and the temperature
is lower than 40°C.
- Before any maintenance or cleaning
operation, check that the wall cutoff switch
is off and the hot water, cold water and steam
taps are closed (the latter applies to steam-
heated machines only).
- Do not load the drum with fabrics that have
been cleaned, dampened, washed or stained
with inflammable or explosive substances.
Otherwise, hand-wash them first.
- Keep inflammable liquids far from the
washing machine, in dry and ventilated
premises, out of the reach of outsiders.
- Keep cleaning products and washing
powders far from the machine, if possible,
closed in a cabinet.
- Do not hamper air inlets or heat-exchanging
openings. Keep an appropriate distance
between the machine and the walls or other
objects.
7.7 ALARMS
E1
Icon
:
water in the tub.
1) Alarm E1: water in the tub.
If water in the tub is detected before the start
of a cycle, all functions are disabled. The
alarm will disappear as soon as water reaches
below the safety level. This alarm does not
involve buzzer actuation and will be removed
by simply switching the machine off and
then on again. The sources of this fault are
either the drain (make sure that the solenoid
valve is clean and in good working order) or
the built-in level pressure switch.
E2
Icon
:
poor water level.
2) Alarm E2: Water level alarm
The water level required by the specific
program has not been reached after taking in
water for 5 minutes. This alarm signal will
automatically disappear as soon as the tub
receives the required amount of water. This
alarm has no effect on the cycle, which is
resumed as soon as the correct water level is
reached.
If the correct level fails to be reached after
water has been taken in for 10 more minutes
the cycle is stopped and the buzzer is
activated. To remove this alarm, just switch
the machine off and then on again. The
21
causes may be poor pressure in the mains, a
blocked filter in the water intake solenoid, a
closed supply tap, a broken drain solenoid
valve or a leak in the same (water is taken in
but it is simultaneously drained and it
consequently fails or is slow to reach the
required level).
Icons
and
E3
:
drain failure.
3) Alarm E3: Drain alarm.
Water has failed to drain below the safety
level after one minute. The cycle will be
resumed after water has reached below the
safety level, with no effect on cycle
completion. The buzzer is not actuated. As
for the causes, see alarm E1.
E4
Icon
heating failure.
4) Alarm E4: Heating alarm
After the heating has worked for 20 minutes,
the temperature has not risen by at least 5°C,
and yet the cycle proceeds normally. This
alarm will automatically disappear as soon
as the temperature reaches the established
threshold. The buzzer is not actuated. The
cause may be an incorrect connection of the
heating elements or either scale or lint on the
heating elements. It is advisable to check
that the hot water inlet has been connected
properly: if the cold and hot water inlets
have been inverted, heating times will be
abnormally increased.
E5
Icon
:
overtemperature.
5) Alarm E5: Overtemperature alarm -
disconnected temperature probe
Water temperature has exceeded 95°C or the
temperature probe is either broken or
disconnected. The wash cycle is aborted and
the buzzer is activated. This alarm can be
cancelled only by switching the machine off
and then on again.
E6
Icon
:
door failed to be locked/unlocked.
6) Alarm E6: Door lock alarm
Ten seconds after cycle start the door has
failed to be locked (i.e. the door is not closed
ten seconds after the START key has been
pressed). The wash cycle is aborted and the
alarm status can be removed only by pressing
the "START" key again. The buzzer is not
alternately
:
Publicidad
Tabla de contenido
