Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
WARNING!:
SHOCK HAZARD. DO NOT OPEN. TO
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
Designed and Engineered by
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
Blackstar Ampli cation Ltd
MOISTURE. THIS APPARATUS MUST BE EARTHED.
Northampton, England
AVIS!:
RISQUE DE CHOC ELECTRIQUE. NE PAS
Made under license in Korea
OUVRIR. POUR EVITER LES RISQUES D'INCENDIE
ET DE DECHARGES ELECTRIQUES, N'EXPOSEZ
JAMAIS CET APPAREIL A L'HUMIDITE OU A LA
PLUIE. CONNECTER CET APPAREIL A LA TERRE.
Rear Panel
1. Speaker Outputs
There are two parallel speaker outputs for connecting external speaker cabinet(s).
When connecting speakers always ensure that the Impedance Selector (2) is set
correctly.
2. Impedance Selector
This control matches the amplifier's impedance to that of the connected speakers.
Always ensure that the selected impedance matches that of the speaker cabinets
connected. See table below.
Cabinets Connected
1 x 16 Ohm cabinet
2 x 16 Ohm cabinets
1 x 8 Ohm cabinet
2 x 8 Ohm cabinets
1 x 4 Ohm cabinet
A speaker cabinet of less than 4 Ohms, or 2 x 4 Ohm cabinets, should not be used
together with this amplifier.
WARNING: The amplifier must always be completely powered down before
adjusting the setting of the Impedance Selector. Failure to do this, or to correctly
match the impedance of the amplifier and speakers, will damage the amplifier.
3. H.T. Fuse
The value of the H.T. Fuse is specified on the rear panel. Never use a fuse of the
incorrect value or attempt to bypass it.
4. Mains Fuse
The value of the Mains Fuse is specified on the rear panel. Never use a fuse of the
incorrect value or attempt to bypass it.
5. Mains Input
The supplied detachable mains lead is connected here. The lead should only
be connected to a power outlet that is compatible with the voltage, power and
frequency requirements stated on the rear panel. If in doubt get advice from a
qualified technician.
12
CAUTION!:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION!:
POUR EVITER LES RISQUES DE DECHARGES
ELECTRIQUES, NE PAS OUVRIR LE COUVERCLE. CET
APPAREIL NE COMPORTE AUCUNE PIECE SUSCEPTIBLE
D'ETRE REPAREE PAR VOS SOINS. FAITES TOUJOURS APPEL
A UN TECHNICIEN QUALIFIE POUR TOUTE REPARATION.
WARNING!:
DO NOT OBSTRUCT VENTILATION GRILLES
ATTENTION!:
NE PAS OBSTRUER LES GRILLES DE VENTILATION
Impedance Selected
16 Ohms
8 Ohms
8 Ohms
4 Ohms
4 Ohms
WARNING!:
RISK OF HAZARDOUS ENERGY
IMPEDANCE
AVIS!:
ENERGIE ELECTRIQUE DANGEREUSE!
SPEAKER OUTPUTS
CONNECT SPEAKERS BEFORE USE
OUTPUT: 30 WATTS RMS
1
2
Channel Blending
The Artisan 30H's topology allows the blending of the two channels. By paralleling
the guitar connection to the inputs of Channel 1 and Channel 2 (see Figure 1 and
Figure 2 below) endless tonal variations can be explored.
Figure 1
Technical Specification
Power (RMS): 30 Watts or 10 Watts (Switchable)
Valves: 1 x GZ34, 4 x EL84, 3 x ECC83, 1 x EF86
Weight (kg): 17.3
Dimensions (mm): 715 x 289 x 208.5
MODEL: ARTISAN30H
H.T. FUSE
MAINS FUSE
MAINS INPUT
T500mAL 250V
230V - T1.6AL 250V
100V 50/60Hz
100V/120V - T3.15AL 250V
160 WATTS
3
4
5
Figure 2
N16549
13
Publicidad
Tabla de contenido
