Maintenance And Care; Troubleshooting - Windsor Saber Blade 16 Instrucciones Importantes De Seguridad

Draining the Recovery tank
Note
If the recovery tank is full the float clos-
es the suction channel. The suction op-
eration is interrupted. Empty the
recovery tank.
Remove the solution tank, as de-
scribed above.
Lift up the recovery tank and carry it
to the disposal site.
Warning
Please observe the local provisions re-
garding the wastewater treatment.
Pour out dirty water.
Rinse the recovery tank with clear
water.
Transport
If you want to transport the appli-
ance on a vehicle secure it from
slipping.
To reduce the required space, the
pushing handle can be folded or disas-
sembled:
Release the star grips of the push-
ing handle fastening.
Unscrew the star grips, remove the
screws and take off the upper push
handle half.

Maintenance and care

Danger
Risk of injury!
Pull the plug from the mains before car-
rying out any tasks on the appliance.
Warning
Risk of damage to the appliance on ac-
count of water leakage. Drain out dirty
water and the remaining free water be-
fore wokring at the machine.
Maintenance schedule
After the work
Warning
Risk of damage. Do not wash down the
appliance with water and do not use
aggressive detergents.
Pour out dirty water.
Rinse the recovery tank with clear
water.
Empty the solution tank.
Fill the solution tank with clear water
and rinse the appliance to avoid
residue buildup.
Remove the remaining water from
the solution tank.
Check the seal in the ball valve in
the solution tank.
Check the lint filter, clean if required
Let the tanks dry prior to closing
them to prevent odor.
Clean the outside of the appliance
with a damp cloth which has been
soaked in mild detergent.
Clean the squeegee, check for wear
and replace the squeegee if re-
quired.
Check the brushes for wear, re-
place if required.
Clean the water distribution bars
above the brushes, remove if nec-
essary and flush with water.
Monthly
Check the condition of the seals be-
tween the appliance and the recov-
ery tank; replace if required.
Clean the brush tunnel.
Yearly
Have the prescribed inspection car-
ried out by the customer service.
Maintenance Works
Replacing the squeegee
Lift the squeegee by activating the
pedal for the squeegee lowering.
Press the push-button for the
squeegee change toward the inside
- the squeegee will release.
Pull off the squeegee downwards.
Remove the screw springs and in-
stall the new squeegee.
Align the new squeegee so that the
locking nose points toward the cen-
tre of the appliance.
Insert the screw springs into the re-
ceptacle on the appliance.
Insert the squeegee into the appli-
ance and lock it in.
Repeat process on the second
squeegee.
Note
Regular exchanges of the two squee-
gee will improve the scraping effect
and will prolong their life.
Replacing the brushes
Lay the device on its side.
Press the brush change key and si-
multaneously tilt the brush roller
downwards.
Pull out the brushes roller.
Place the new brush roller on the
driver and lock into place.
Maintenance contract
To ensure a reliable operation of the
appliance maintenance contracts can
be concluded with the competent
Windsor sales office.
Frost protection
In case of danger of frost:
Empty the solution and recovery
tank .
Push the button for detergent solu-
tion until no more water is expelled.
Store the appliance in a frost-pro-
tected room.

Troubleshooting

Danger
Risk of injury!
Pull the plug from the mains before car-
rying out any tasks on the appliance.
Warning
Risk of damage to the appliance on ac-
count of water leakage. Drain out dirty
water and the remaining free water be-
fore wokring at the machine.
In case of faults that cannot be reme-
died using the table below please con-
tact the customer service.
7
English