DSC iotega Guía De Usuario De Inicio Rápido página 2

Using the integrated keypad
Stay arming arms the perimeter of the premises while permitting movement inside.
Away arming arms the entire system, including the perimeter and interior devices.
1. Ensure the Ready LED is on, then enter your user code.
2. For Away arming, exit the premises.
3. When the exit delay expires, the system is armed.
To disarm the system or to cancel the arming sequence, enter your user code.
Note: If the user code is incorrect, a 2-second error tone sounds. Tap [#] and try again.
When there is a trouble condition, the Trouble LED
Note: The Trouble LED flashes if you need your access code to silence the beeps (UL/ULC requirement).
Refer to the full user manual online for more information on trouble codes.
IMPORTANT: EMERGENCY USE ONLY!
Use these keys to send emergency signals to the monitoring station.
1. Tap the Shift key .
2. Touch and hold the Fire, Auxiliary, or Panic key for 2 seconds. The system beeps to indicate the alarm
input was accepted and transmission is underway.
The Fire key activates the siren in the pulsed fire pattern.
For Auxiliary alarms, the system beeps again when the monitoring station acknowledges the signal.
The Panic alarm is completely silent. Your installer can program this alarm to be audible.
3. Tap the [#] key to return to the number keypad.
PRIVACY STATEMENT:
The Tyco cloud collects the following Data from the iotega panel (public IP address, security events and statuses, security configuration, and system diagnostics) in order to [improve system
performance, troubleshoot customer issues, and improve user experience ]. You have the right to access, correct and request removal of your personal data by contacting info@tycosecurityproducts.com and the right to
lodge a complaint with a supervisory authority. Tyco will not transfer this data to other parties, except for our cloud service provider in the US, with whom we have contractual Personal Data Processing Terms and EU
Standard Contractual Clauses. Tyco uses industry-standard safeguards to protect your personal information. Find out more in our Privacy Statement at www.tyco.com/privacy. Your personal information will be retained
as long as necessary to achieve the purpose for which it was collected and for any period thereafter as legally required or permitted by applicable law.
SIMPLIFIED DECLARATION OF CONFORMITY:
compliance with Directive 2014/53/EU.
The following models are covered by this guide: WS900-14, WS900-24, 3G7090, LT7090 (used in North America only), WS901-14, WS901-24EU, WS901-18, WS901-28 and 3G7090-EU.
The full text of the EU declarations of conformity for the models mentioned below are available at the following internet addresses:
Model WS901-14: http://dsc.com/pdf/1707001
Model WS901-24EU: http://dsc.com/pdf/1707002
Model WS901-18: http://dsc.com/pdf/1707003
Model: WS901-28: http://dsc.com/pdf/1707004
Model: 3G7090-EU: http://dsc.com/pdf/1707005
OPERATING FREQUENCY BANDS AND RELATED MAX RADIO-FREQUENCY POWER TRANSMITTED:
433.04 MHz – 434.79 MHz: 10 mW
868.0 MHz – 868.6 MHz and 868.7 MHz – 869.2 MHz: 10 mW
2400 MHz – 2483.5 MHz: 100 mW
E-GSM 900: 2 W, EDGE 900: 0.5 W
DCS 1800: 1 W, EDGE 1800: 0.4 W
FDD I/VIII: 0.25 W
EUROPEAN SINGLE POINT OF CONTACT: Tyco Safety Products, Voltaweg 20, 6101 XK Echt, Netherlands.
© 2017 Tyco Security Products. All Rights Reserved. www.dsc.com
Arming the system
Disarming the system
Viewing system troubles
turns on and the system beeps every 10 seconds. Tap any key to silence the beeps.
Using the emergency keys
Hereby, Tyco Safety Products Canada Ltd declares that the radio equipment type Wireless Alarm System with Integral Cellular Alarm Communicator is in