Setting Parameters - Ecoflam OILFLAM500.1 PR/MD Manual Del Usuario

LB1421 Oilflam 500.1-600.1 PR/MD
When the burner is ignited all displays of the regulator light up. The set point display will blink for about 10 seconds. The value
in the upper field of the display (red) indicates the actual value. The value in the lower field of the display (green) indicates the set
point currently programmed.
CHANGING THE SET POINT
To change the set point, proceed as follows: - -
- - Change the value of set point SP1 using the t and s keys. e
- -
return to normal display press
* * The value of SP1 depends on the value set previously in configuration level C111.
SETTING PID PARAMETERS
PID parameters are factory set to standard mean values. The operation of the regulator can be self-adapted to suit the system by
activating the "tunE" function. The regulator will set the PID parameters automatically. To activate the "tunE" function proceed
as follows: - - - - With the burner in operation, press
blinking, the self-adaptation routine has been completed. - -
* * The "tunE" function cannot be activated in Manual mode, or when the burner is off.
The PID parameters can be corrected manually from the parameters level, working on the proportional band Pb1, the
derivative action time dt and the integral action time rt.
To change parameters Pb1, dt and rt, proceeds as follows: - -
one parameter to the next, press
Confirm the changed parameters by pressing
automatically. - - - - Press PGM to access the next parameter. - -
PGM
PGM to access the next parameter. - -
DIFFERENTIAL SETTING FOR IGNITION AND SHUTOFF
The regulator allows the selection of an adjustable switching differential that establishes burner ignition and shutoff values.
HYS1 indicates the lower ignition limit, below which the regulator switches the burner to maximum power. HYS3 indicates
the upper shutoff limit, above which the regulator switches the burner off. To set HYS1 and HYS3 proceed as follows: - -
the PGM PGM key to access the parameters level. - -
(burner ignition differential-stage II), increase or decrease the value using the
pressing PGM. - - - - If confirmation is not given within 2 seconds the value will be stored automatically. - -
PGM
next parameter. - - - - When HYS2 is displayed (burner shutoff differential-stage II), repeat the procedure described above. - -
PGM to access the next parameter. - -
PGM
- - To return to normal display press
- -
MANUAL/AUTOMATIC MODE
To access "MANUAL" mode, press and hold
in operation. It is deactivated automatically when the burner shuts off. When the LED above the hand symbol is alight, the
regulator is in manual mode and the position of the servocontrol can be changed using the
of the regulator indicate whether the servocontrol OPEN or CLOSE command is currently active. Pressing the
servocontrol OPENS. Pressing the
seconds. The LED above the hand symbol goes out and the regulator reverts to automatic.
The RWF 40 regulator can be set with the set point interlocked to the external probe. To select this operating mode, proceed as
follows: - - - - Connect the required probe as in the wiring diagram. - -
the regulator must be set as follows: - -
displayed, use the key to access the second figure (XXXX). Use the
change of parameters by pressing
access the configuration level. When the display reads C112 (XXXX), use the
key to set the type of probe (XX3X). - -
within 2 seconds the value will be stored automatically.
- - To return to normal display press
- -
- - Press PGM to access the parameters level. - -
- - PGM
displayed (heating curve gradient), increase or decrease the value using the
pressing PGM. - - - - If confirmation is not given within 2 seconds the value will be stored automatically.
PGM
- - To return to normal display press
- -
ABCD

SETTING PARAMETERS

- - Press the PGM button to access the user level. SP1* will appear in the lower display
PGM
EXIT.
EXIT
PGM +
PGM
PGM . - - PGM - - When Pb1 is displayed, the value can be increased or decreased using the s and t keys. - -
PGM. - - - - If confirmation is not given within 2 seconds the value will be stored
PGM
- - When rt is displayed, repeat the procedure above. - -
- - To move from one parameter to the next, press
- - When HYS3 is displayed (upper shutoff differential) repeat the procedure described above.
EXIT.
EXIT
EXIT for at least 5 seconds. Manual mode can only be selected when the burner is EXIT
key the servocontrol CLOSES. To select automatic mode press and hold
CLIMATIC COMPENSATION
- - Press the PGM key to access the configuration level. When the caption C111 (XXXX) is
PGM
PGM. If this is not done within 2 seconds, the value is stored automatically - -
PGM
- - Confirm the changed parameters by pressing
EXIT. To establish the heating curve, proceed as follows:
EXIT
- - Press PGM to move from one parameter to the next. - -
PGM
EXIT.
EXIT
. - - - - After a 2 second delay the value set is stored automatically – To
. - - - - the caption "tunE*" will blink in the display. – When "tunE" stops
- - Confirm the computed parameters by pressing the
- - Press the PGM button to access the parameters level. - -
PGM
- - When dt is displayed, repeat the procedure described above. - -
and
- - Change the regulator settings. When using an external probe
key to select the type of probe (XX3X). - -
key to access the second figure (XXXX). Press the
and
- pag.24 -
- - To return to normal display press
PGM . - - PGM - - When HYS1 is displayed
keys. - - - - Confirm the changed parameters by
- - Press PGM to access the
PGM
and keys. The LEDS on the front
PGM. - - PGM - - If confirmation is not given
- - When the letter H is
keys. - - - - Confirm the changed parameters by
key for 2 seconds.
- - To move from
- -
- - Press
EXIT.
EXIT
- - Press
- - Press
key the
EXIT for at least 5
EXIT
- - Confirm the
- - Press PGM to
PGM