EdilKamin MIMI’ Instalación Uso Y Mantenimiento página 33

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 59
INSTRUCTIONS FOR USE
SETTINGS
Setting the clock
Press the MENU button for 2 seconds and use the + and – keys to follow the instructions given on the display to access the 'Clock'
menu.
This allows you to set the time on the electronic control board.
Then press MENU and the following data appears in sequence – this can be adjusted:
day, month, year, hour, minutes, day of the week.
When 'Save?' appears on the display, you can check that the settings have been entered correctly before confirming. Press MENU to
save the information ('Save OK' then appears on the display).
Weekly timer
Programmer to ignite and shutdown the stove at various times during the week.
Press the MENU button on the remote control for 2 seconds to access the time setting function and press the + key to access the
weekly timer function – 'Program ON/OFF' will appear on the display.
The timer allows you to set a number of ignitions and shutdowns per day (up to a maximum of three), for each day of the week.
As you confirm via the MENU button, one of the following options will appear:
No Prog. (no program is set)
Program/daily (a single program is set for every day)
Program/weekly (a program is set for each day of the week)
Move from one to the other using the + and – keys.
Use the MENU button to confirm the 'Daily program' option and access the selection of the number of programs
(ignition/shutdown) to be set per day.
Use the 'Program/daily' option to set the identical program/s for every day of the week.
The following will be displayed if the + key is pressed:
- No Prog.
- Prog. No. 1 (one ignition and one shutdown per day), Prog. No. 2 (same as before), Prog. No. 3 (same as before)
Use the ___ button to show them in reverse order.
If the 1st program is selected, the ignition time is shown.
The display shows: 1 Ignition Hour 10.30; use the +/– keys to change the hour and press MENU to confirm.
The display shows: 1 Ignition Minutes 10.30; use the +/– keys to change the minutes and press MENU to confirm.
In the same way, adjust the shutdown times. The program is confirmed by pressing the MENU button when "Saved" appears on the
display.
When confirming 'Program/week', you will need to choose the day to which the program is to apply:
1 Mon; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sat; 7 Sun
Once you have chosen the day by scrolling through them with the + and – keys, confirm by pressing MENU and
proceed with the settings of the programs in the same way as for the 'Program/daily', selecting whether or not to enable
a program for each day of the week and choosing the number and times of interventions.
Should you make a mistake whilst setting the programs you can exit without saving by pressing the 0/1 key and 'Saved' will appear
on the display.
Pellet reserve warning
The MIMI' - NORMA thermal stoves are equipped with an electronic pellet detection system.
The pellet detection system is integrated into the electronic control board, allowing the stove to monitor how many kilos of pellets are
left. This verification is implemented at any point whilst the stove is in operation mode.
For correct system operation, it is important that the following procedure is adhered with during the first ignition (that must be
implemented by the DEALER).
Before starting to use the pellet detection system, you must load and consume a full sack of pellets. This allows for a brief running-in
of the loading system.
Then press the 'reserve' button once, thereby storing the data into the memory that 15 kg have been loaded.
From now on the display will show the remaining pellets as they decrease in kg (15...14...13).
Each time pellets are reloaded you must enter the quantity. E.g. when loading 15 kg, simply press the 'pellet load' button to enter this
into the memory. For other quantities, or in the event of an error, you can specify the quantity using the pellet reserve menu as
follows:
Press the MENU button for 2 seconds to view the SETTINGS. Press + or – consecutively to view T. Max exit.
Confirm by pressing MENU and the remaining quantity of pellets will be displayed + that being loaded (default is 15 and can be
changed using the +/- keys).
Should the hopper run out of pellets, the stove will block and 'Stop Flame' will appear.
33

Publicidad

Tabla de contenido
loading

Tabla de contenido