Operating The Machine; Starting The Engine; Starting The Gasoline / Petrol Engine; Starting The Lpg Engine - Nilfisk-Advance Condor XL Instrucciones De Uso

OPERATING THE MACHINE

The Condor XL™ is a rider-type automatic fl oor scrubbing machine. It is designed to lay down cleaning solution, scrub the fl oor, and vacuum dry all in one pass.
The controls on the Condor XL were designed with one touch operation in mind. For single pass scrubbing the user can simply depress one switch and all scrub
functions on the machine will be activated.
NOTE: Bold numbers in parentheses indicate an item illustrated on pages 6-9.
NOTE!: MAKE SURE THE FOOT PEDAL IS IN THE NEUTRAL POSITION. THE ENGINE WILL NOT CRANK IF THE FOOT PEDAL IS NOT IN
NEUTRAL.
STARTING THE DIESEL ENGINE
1 Turn the key switch (50) clockwise to the RUN (ON) position. The glow plugs will activate for 10 seconds as indicated by the attention indicator (66) and the
glow plug icon (66d) on the display. If the engine is already warm, turn the key switch to the start position to crank the engine. If the engine is cold, wait for
the attention indicator and glow plug icon to turn off before cranking the engine. The engine should start immediately. If the engine does not start within 15
seconds release the key, wait for approximately one minute and repeat the above steps.
2 Let the engine run at IDLE speed for fi ve minutes before using the machine.
3 Press the Engine Speed Switch (51) once to switch to FULL THROTTLE and move the machine around for two to three minutes at slow speed to warm up
the hydraulic system.

STARTING THE GASOLINE / PETROL ENGINE

1 Turn the Ignition Key Switch (50) clockwise to the START position and release it as soon as the engine starts. If the engine does not start after cranking for
15 seconds, release the key, wait for 1 minute, then try again.
2 Let the engine run at "IDLE" speed for 5 minutes before using the machine.
3 Push the Engine Speed Switch (51) once to switch to "FULL THROTTLE" and move the machine around for 2 or 3 minutes at a slow speed to warm up the
hydraulic system.

STARTING THE LPG ENGINE

1 Open the service valve on the LP fuel tank.
2 Turn the Ignition Key Switch (50) clockwise to the START position and release it as soon as the engine starts. If the engine does not start after cranking for
15 seconds, release the key, wait for 1 minute, then try again.
3 Let the engine run at "IDLE" speed for 5 minutes before using the machine.
4 Push the Engine Speed Switch (51) once to switch to "FULL THROTTLE" and move the machine around for 2 or 3 minutes at a slow speed to warm up the
hydraulic system.
ALWAYS operate the machine with the Engine Speed Switch at full throttle. Use the Drive Pedal (29) not the Engine Speed Switch (51) to control the speed
of the machine. The speed of the machine will increase as the pedal is pushed closer to the fl oor. Do not press the Drive Pedal (29) until the engine has started.
Engine Speed Switch (51):
There are three engine speed settings that can be selected by the engine speed switch (51) on the control panel.
1 "Idle" (1200 RPM – Petrol / LPG) (1300 RPM – Diesel). Use for warm up and cool down. The engine speed switch light will be off.
2 "Run" (2200 RPM). Use for transporting and most scrubbing operations. The engine speed light will be on.
3 "Turbo" (2400 RPM). Use only for heavy engine load situations such as heavy scrubbing on inclines. The engine speed light will be on.
4 To select between Idle and Run press and release the engine speed switch.
5 To select the Turbo speed, fi rst set the speed to Run. Then press and hold the engine speed switch for 2 seconds. To go back to Run speed, press the switch
again.
6 The Condor XL has an automatic idle feature that will reduce the engine speed to idle when the foot pedal (29) has been in the neutral position for 20
seconds or more. The selected engine speed will automatically resume when the foot pedal is moved from neutral. If the engine speed switch (51) is pressed
while in idle-override, the automatic idle feature will be temporarily disabled until the next time the foot pedal is moved from the neutral position. This can be
useful during troubleshooting or if it is desired to let the machine run at full speed for warming up.
ENGLISH / A-15
FORM NO. 56041705 - Condor XL™ - A-15