Additional Safety Rules - GreenWorks 32042a Manual Del Propietário

existing walls or other blind areas. The protruding
blade may cut objects that can cause kickback.
Check lower guard for proper closing before each
use. Do not operate saw if lower guard does not move
freely and close instantly. Never clamp or tie the lower
guard into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the lower
guard with the retracting handle. Make sure it moves
freely and does not touch the blade or any other part,
in all angles and depths of cut.
Check the operation of the lower guard spring. If
the guard and the spring are not operating properly,
they must be serviced before use. Lower guard may
operate sluggishly due to damaged parts, gummy
deposits, or a buildup of debris.
Lower guard should be retracted manually only for
special cuts, such as "plunge cuts" and "compound
cuts." Raise lower guard by retracting handle. As soon
as blade enters the material, the lower guard must be
released. For all other sawing, the lower guard should
operate automatically.
Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch
is released.
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this power
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear safety glasses with side shields that
comply with ANSI 287.1. Everyday glasses have only
impact resistant lenses. They are not safety glasses.
Following this rule will reduce the risk of eye injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating
condition. Be aware of possible hazards when not
using your battery tool or when changing accessories.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.Always wear safety
glasses with side shields that comply with ANSI 287.1.
Everyday glasses have only impact resistant lenses.
They are not safety glasses. Following this rule will
reduce the risk of eye injury.

ADDITIONAL SAFETY RULES

Check damaged parts. Before further use of the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by
an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
Inspect for and remove all nails from lumber before
English(original instructions)
(1  
using this tool. Following this rule will reduce the risk
of serious personal injury.
Do not operate tool while under the influence of
drugs, alcohol, or any medication. Following this rule
will reduce the risk of electric shock, fire, or serious
personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and
possibly injury.
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal injury, never use
any cordless product in the presence of open flame.
An exploded battery can propel debris and chemicals.
If exposed, flush with water immediately.
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than
ƒ) EXW OHVV WKDQ ƒ) 'R QRW VWRUH RXWVLGH RU LQ
vehicles.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for
at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of
serious personal injury.