Before Using The Machine - Sharp AL-1035-WH Guia De Inicio Rapido

English-START GUIDE
This guide indicates important points to note for installation and usage. Read and understand
this guide to ensure that you install the machine correctly. The Operation Guide for the machine
is on the accompanying CD-ROM. Read the Operation Guide to make full use of all the
machine has to offer.
Caution!
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Laser information
Wave length
Pulse times (North America and Europe)
Output power
Caution!
Use of controls or adjustments or performance of procedures other than those specifi ed
herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007)
CAUTION
VORSICHT
ADVARSEL
ADVERSEL
VARNING
VARO!
CAUTION
VORSICHT
ADVARSEL
Installation precautions (Note):
• Do not install the machine on an unstable or
slanted surface. Please install the machine
on a surface which can withstand the weight
of the machine.
• Do not install the machine in the place which
is directly exposed to sunlight, which may
result in machine failure.
• Do not install the machine in a location with
poor air circulation.
(A small amount of ozone is created inside the
machine during printing. The amount of ozone
created is not suffi cient to be harmful; however, an
unpleasant odor may be noticed during large copy
runs, and thus the machine should be installed in a
room with a ventilation fan or windows that provide
suffi cient air circulation. The odor may occasionally
cause headaches.)
* Install the machine so that people are not directly
exposed to exhaust from the machine.
• Be sure to allow the required space around the
machine for servicing and proper ventilation.
20 cm
10 cm 10 cm
785 nm +10 nm/-15 nm
(41.63 μs ± 100 ns)/7 mm
Max 0.7 mW
ADVERSEL
VARNING
VARO!
• Do not install the machine in a location
with moisture or dust, which may result in
machine failure.
• Do not install the machine in places near
alcohol, paint thinner or other combustibles.
(Because it may result in fi re or electric shock, if the
combustibles contact any electrical part inside the
machine)
• Do not install the machine in places with
obvious changes of temperature and humid-
ity, such as places near heaters, humidifi ers
or air-conditioners.
(In the event of any large
temperature changes, such as moving the machine
from a cold place outdoors into a warm place indoors,
the inside of the machine may generate condensation.
If any condensation occurs, allow for adjustment of
the machine temperature to the room temperature
by letting it sit for at least 2 hours before using the
machine.)
• The machine shall be installed in a place which
is accessible to power socket for connecting the
power. Connect the machine to a power socket
which is not used by other electrical equipment. If
lighting devices are connected to the socket, the
lights may blink.
Environment information
This product is designed for commercial application only and as such it falls outside the scope
of Regulation (EC) 1275/2008 implementing EU Directive 2005/32/EC on eco-design require-
ments for standby and off mode electric power consumption. Sharp does not recommend the
product for domestic application and will not accept any liability for such use.
Products that have earned the ENERGY STAR
environment through superior energy effi ciency.
The products that meet the ENERGY STAR
The products without the logo may not meet the ENERGY STAR
CONTENTS
BEFORE USING THE MACHINE ....................................................................EN1
MACHINE APPEARANCE AND FUNCTIONS INTRODUCTION ...................EN2
SPECIFICATIONS ...........................................................................................EN4
SUPPLIES .......................................................................................................EN4
INFORMATION ON DISPOSAL FOR USERS (PRIVATE HOUSEHOLDS) ..EN4

BEFORE USING THE MACHINE

Please pay attention to the following items when using the machine.
The machine is a precision instrument. When the machine is subject to falling, vibra-
tion shock, fi re or electric shock, please turn off the power and remove the power
plug from the outlet, then contact your dealer or nearest service representative.
Power notes (Warning):
• Be sure to connect the power cord only to a
power outlet that meets the specifi ed voltage
and current requirements. Also make certain
the outlet is properly grounded. Do not use
an extension cord or adapter to connect
other devices to the power outlet used by the
machine. Using an improper power supply
may cause fi re or electrical shock.
(For the power supply requirements, see the name
plate at the bottom of the machine.)
Power notes (Note):
• Apart from the factory-supplied power
supply line of the machine, do not use other
power lines. Otherwise it may result in fi re or
electric shock.
• When removing the power plug from the
outlet, do not pull on the cord.
cord may cause damage such as wire exposure and
breakage, and may result in fi re or electrical shock.)
• If you will not use the machine for a long
time, be sure to remove the power plug from
the outlet for safety.
Handling precautions (Warning):
• Do not put containers with water or other
liquids, or any metal objects which may fall
into the machine, on the machine or beside it.
(If the liquid spills out or any object falls into the
machine, it may result in fi re or electric shock.)
• Do not put heavy objects on the machine, or
press forcefully on the document glass.
(Otherwise, the machine components may be
damaged.)
• Do not remove the case of the machine.
(The high-voltage parts inside the machine may
produce electric shock.)
• Do not alter the machine in any way.
(Any alteration may result in personal injury or
machine damage.)
• Do not clean the machine with the fl am-
mable spray.
(If the gas in the spray contacts the thermionic
component or the fusing unit inside the machine, it
may result in fi re or electric shock.)
Handling precautions (Note):
• Do not look directly at the light source.
(It may hurt your eyes.)
• Do not block the air vent of the machine.
Do not install the machine in a place which
blocks the air vent.
(Blocking the air vent may result in heat accumulation
inside the machine, which may cause the risk of fi re.)
• Move the machine with its handle, and
handle it with great care.
(Before moving the machine, please close the cover,
retract its feeder tray and output tray, turn off the
power switch and unplug the power plug. Then hold
its handle tightly, erect the machine slowly to lift it.)
A2
are designed to protect the
®
® guidelines carry the logo shown above.
guidelines.
®
• Do not damage or modify the power cord.
(Placing heavy objects on the power cord, pulling it,
or forcibly bending it will damage the cord, resulting in
fi re or electrical shock.)
• Do not insert or remove the power plug with
wet hands, otherwise it may result in electric
shock.
• When moving the machine, switch off the
main power and remove the power plug from
the outlet before moving.
damaged, creating a risk of fi re or electrical shock.)
• Do not bundle the power line, otherwise it
(Pulling on the
may result in fi re or electric shock.
• Please plug the power plug completely into
the power socket, otherwise it may result in
fi re or electric shock.
• This machine is precision equipment. If ma-
chine is dropped or got a hard shock, or, if
there is any smoke, smell or other abnormal
phenomenon, do not use the machine.
(If the machine is used in any of the above cases, it
may result in fi re or electric shock. Please turn off the
power switch immediately and unplug the power plug
from the socket. Please contact your dealer or the
nearest authorized service department.)
• In case of a thunderstorm, please turn off
the power switch and unplug the power plug
from the socket to avoid electric shock and
fi re incurred by lightning.
• If metal or water falls into the machine,
please turn off the power switch and unplug
the power plug from the socket.
(Please contact your dealer or the nearest authorized
service department. Under this circumstance, using
the machine may result in electric shock or fi re.)
• When removing paper jammed, performing
maintenance and closing the cover, please
beware of clamping your fi nger.
• The fusing unit and paper output area are
very hot. Do not touch them when removing
the paper jammed. Be careful not to burn
yourself.
• Do not touch the drum cartridge.
(If there are any scratches or stains on the drum
cartridge, it will cause smudges on the copies.)
• Do not throw toner or the toner cartridge into fi re.
(The toner may splash and result in burns, so please
keep the toner out of reach of children.)
Please give priority to using the
toner that came with the machine.
• When transporting by car, please put the
machine into its original box and place it
on a stable surface (such as on a seat).
(Do not leave the machine in the car for a long
time, as the temperature inside the car may exceed
its allowed range. In addition, avoid bumpy roads
since the bumps may result in machine failure.)
(The cord may be
A1
A3
EN1