Beretta Ciao S 20 C.S.I. Instrucciones De Instalacion Y Uso página 5

24 C.S.I. - 24 R.S.I.
Pipe length
ø 80 [m]
2
from 2 to 8
from 8 to 25 not installed
(**) fitted in boiler
CONCENTRIC OUTLETS (ø 60-100)
The boiler has been designed to be connected to concentric outlet/suc-
tion pipes and with the opening for air suction (E) closed (fig. 10b). The
concentric outlets can be places in the most suitable direction according
to room requirements, complying with the maximum lengths indicated
in the table. For installation, follow the instructions supplied with the kit.
According to the length of the pipes used, it is necessary to insert a
flange, selecting one from those contained in the boiler (see the follow-
ing table). When necessary, the flue gas flange (F) must be removed
using a screwdriver as a lever. The table indicates the permitted linear
lengths. According to the length of the pipes used, it is necessary to
insert a flange, selecting one from those contained in the boiler (see
the following table).
20 C.S.I.
Pipe length
ø 60-100 [m]
up to 0,85
from 0,85 to 2,35
from 2,35 to 4,25
(**) fitted in boiler
24 C.S.I. - 24 R.S.I.
Pipe length
ø 60-100 [m]
up to 0,85
from 0,85 to 2,35
from 2,35 to 4,25
not installed
(**) fitted in boiler
Concentric pipes (ø 80/125)
The boiler has been designed to be connected to concentric outlet/
suction pipes and with the opening for air suction closed. The concen-
tric outlets can be placed in the most suitable direction according to room
requirements, complying with the maximum lengths indicated in the table.
For installation, follow the instructions supplied with the kit. To go
through the wall, drill a hole of Ø 140 mm. According to the length
of the pipes used, it is necessary to insert a flange selecting from
those contained in the boiler (see table). Pay special attention to
external temperature and pipe length. Refer to the diagrams in order
to establish if it is compulsory or not to use a condensation collector.
In case of operation at temperature lower than 60 °C, it is compulsory
to use a condensation collector. If a condensation collector is used,
provide a slope of the flue exhaust pipe of 1% towards the collector.
Connect the condensation trap syphon to a white water outlet pipe.
Non insulated outlet pipes are potential sources of danger.
20 C.S.I.
Pipe length
Ø 80 125 [m]
from 0,96 to 3,85
from 3,85 to 7,85
from 7,85 to 12,40
(**) fitted in boiler
Load losses for each
Flue gas
bend (m)
flange (F)
45°
Ø 42
1,2
Ø 44 (**)
Load losses for each
Flue gas
bend (m)
flange (F)
45°
Ø 39
1
Ø 41 (**)
Ø 43
Load losses for each
Flue gas
bend (m)
flange (F)
45°
Ø 42
1
Ø 44 (**)
Load losses for each
Flue gas
bend (m)
flange (F)
45°
Ø 39
1,35
Ø 41 (**)
Ø 43
MAXIMUM LENGTH OF CONCENTRIC PIPES
90°
1,7
To direct the outlets in the most suit-
able installation way (right air input)
there is an air/flue gas splitter kit
available.
90°
reduced concentric bend kit
1,5
If it is necessary to install Ciao S on existing systems (replace-
90°
ment of Ciao N/Ciao range), there is a "reduced concentric bend"
kit that allows boiler positioning while keeping the same flue
gas hole.
1,5
Pipe length with
reduced bend [m]
up to 1.85
from 1.85 to 4.25
24 C.S.I. - 24 R.S.I.
Pipe length
Ø 80 125 [m]
90°
from 0,96 to 3,85
2,2
from 3,85 to 7,85
from 7,85 to 12,4
(**) fitted in boiler
CIAO S C.S.I. - CIAO S R.S.I.
COMPULSORY
CONDENSATE BASIN
NON-COMPULSORY CON-
OUTSIDE TEMPERATURE (°C)
Flue gas flange (F)
Ciao S
Ciao S
20 C.S.I.
24 C.S.I.
Ø 41
Ø 44
Ø 43
no flange
Flue gas
flange (F)
Ø 42
(**)
Ø 44
not installed
Ø 80/125
DENSATE BASIN
air/flue gas
splitter
Load losses for
each bend (m)
90°
45°
1.5
1
Load losses for each
bend (m)
45° 90°
1,35 2,2
5