Confi Guring Transporter; Set Up Networking; Select A Music Source - Logitech Transporter Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 77
10
Confi guring Transporter
The instructions below use the remote control to set up Transporter. You can also use the front
panel controls. To scroll up and down, turn the knob on the front panel. Pressing the center of
the knob is equivalent to pressing the
RIGHT
on the front panel is the same as pressing the
panel are the same as the corresponding buttons on the remote.
When you plug in Transporter, the Slim Devices logo is displayed briefl y, followed by a welcome
message.

Set Up Networking

1. Press the
RIGHT
arrow on the remote control. The Set Up Networking menu option
is displayed.
2. Press the
RIGHT
arrow to enter networking setup.
3. Choose whether you want to connect Transporter to a wireless or wired network
by pressing the
and
arrows on the remote. When you have made your
UP
DOWN
selection, press the
arrow. If you are using an ethernet connection, skip to step
RIGHT
7.
4. Transporter prompts you for your local region or country. Scroll using the
arrow on the remote until you fi nd the local region. Press the
your region.
Note: Failure to select the appropriate region may violate local laws.
5. Transporter will scan to fi nd your wireless network. Select your network name (SSID)
and press the
RIGHT
arrow.
If you are in an area where there are multiple wireless networks, you can scroll
down using the remote until you fi nd the one you want to use. If your router is not
broadcasting your network name, you will need to select "Enter a network name".
Tip: You can use the number buttons on the remote to enter text as you might
on a cell phone. Use the PLAY button on the remote as a backspace and the ADD
button to insert a letter.
Logitech
arrow on the remote. Pressing the
button
BACK
arrow. The other buttons on the front
LEFT
DOWN
RIGHT
arrow to select
®
Transporter
Owner's Guide
6. If your network is secured with WEP or WPA encryption, you'll need to enter the
network password or key using the numbers and letters on the remote and press
the
arrow. If your network supports more than one type of encryption
RIGHT
at a time or is not broadcasting its SSID, Transporter may fi rst ask you to choose
your encryption method.
Tip: WEP keys consist of a string of ten or twenty-six digits or letters A through F.
WPA passwords are a string of letters, numbers or punctuation.
Enter the subnet mask for the network, the default gateway IP address, and the
address of your DNS server, pressing the
one.
Tip: If you are having trouble connecting to your wireless network, check the
Frequently Asked Questions section at the end of this guide.

Select a Music Source

1. If SqueezeCenter isn't already running, start it now.
Transporter will scan your local network to fi nd the computer that's running
SqueezeCenter. If you started SqueezeCenter after confi guring Transporter, you may
need to scroll to fi nd it.
Tip: If SqueezeCenter is running on your computer and you don't see it in this
menu, check the Troubleshooting section at the end of this guide and make sure
that any fi rewall software you have installed is confi gured properly.
You can also choose to connect to the SqueezeNetwork internet service.
See the SqueezeNetwork section of this guide for more information.
2. Select the computer you want to use. If you are running SqueezeCenter on multiple
computers on your local network, you can use the
you want to use.
3. Press the
RIGHT
Setup is complete.
Tip: If you want to go back to setup later press the
down and hold it for fi ve seconds. Transporter will return to the Set Up
Networking menu.
RIGHT
arrow on the remote to move to each
DOWN
arrow to scroll to the one
arrow on the remote to connect.
LEFT
arrow on the remote
11

Publicidad

Tabla de contenido
loading

Tabla de contenido