Tabla de contenido
Publicidad
3.4 Making Connections: Use only connectors designed for use with this equipment, suitable to each application. Ensure all connections are
compatible in size and strength. Do not use equipment that is not compatible. Visually ensure all connectors are fully closed and locked.
Connectors (snap hooks and carabiners) are designed to be used only as specified in each product's user instructions.
3.5 Personal Fall Arrest System: The anchor meets the requirements of an OSHA fall protection anchor. An anchorage selected for PFAS must be
able to sustain a load of:
a)
Two times the maximum arrest force permitted when certification exists, or
b)
5,000 lbs., (22.2 kN) in the absence of certification.
An FBH must be worn when this equipment is used as a component of a PFAS.
If the maximum free fall distance must be exceeded, the employer must document, based on test data, that the maximum arresting force will not
be exceeded, and the personal fall arrest system will function properly.
3.5.1 Restraint System: An anchorage selected for restraint must be able to support a static load applied in the direction permitted by the system
of at least:
a)
Two times the foreseeable force when certification exists, or
b)
1,000 lbs. (4.4 kN) in the absence of certification.
An FBH must be worn when this equipment is used as a component of a restraint system. As required by OSHA, the restraint system must prevent
the user from reaching a fall hazard area. Free fall is not permitted.
3.6 Definitions: The following are definitions of terms.
Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard
(otherwise referred to as "user" for the purpose of these instructions).
Certified Anchorage: An anchorage for fall arrest, positioning, restraint, or rescue systems that a qualified person certifies to be capable of supporting the
potential fall forces that could be encountered during a fall or that meet the criteria for a certified anchorage prescribed in this standard.
Competent Person: One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are
unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
Qualified Person: A person with a recognized degree or professional certificate and with extensive knowledge, training, and experience in the fall
protection and rescue field who is capable of designing, analyzing, evaluating and specifying fall protection and rescue systems to the extent
required by this standard.
Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.
4. INSTALLATION AND OPERATION
Do not alter or intentionally misuse this equipment. Consult FallTech when using this equipment in combination with components or
Do not use rebar hooks, large carabiners or large snap hooks to connect to the FBH dorsal D‐rings or to any small diameter non‐compatible
Use caution and take action to avoid excessively sharp and/or abrasive surfaces and edges.
Avoid electric hazards. Use caution when performing arc welding. Arc flash from arc welding operations, including accidental arcs from electrical
Examine the work area. Be aware of the surroundings and workplace hazards that may impact safety, security, and the functioning of fall arrest
systems and ancillary components. Hazards may include but not be limited to cable or debris tripping hazards, equipment failures, personnel
mistakes, moving equipment such as carts, barrows, fork lifts, cranes, or dollies. Do not allow materials, tools, or equipment in transit to
contact any part of the anchor or fall arrest system and/or ancillary components. Pay special attention to the lifeline. Do not work under
Installation of anchorages must be under the supervision of a competent person trained in their design and use.
NOTE: Approved fall protection may be required during installation of the anchor discussed in this manual.
DO NOT use any anchorage discussed in this manual until the system has been completely installed, inspected, and approved for use by a
competent person.
When the anchor is installed as a single point anchor with lag screws, the anchor is an OSHA compliant 5,000lb anchor when loaded in the manner
and direction detailed in this manual.
4.1 Fall Clearance Distance: Take action to reduce the danger of falls. Ensure sufficient clearance exists in the fall path to arrest the fall before
striking the ground or other obstructions. The actual clearance required is dependent upon the type of connecting subsystem used (SAL, SRD, etc.).
Swing fall conditions will increase the fall clearance required. Consult the PFAS manufacturer's user instruction manual.
4.2 Swing Fall: Swing falls occur when the anchorage point is not directly above the point where a fall occurs, as shown in Figure 6 of Appendix B.
The total fall distance may be greatly increased during a swing fall. The force of striking an object in a swing fall may cause serious injury. Minimize
swing falls by installing anchors at least six feet from exposed roof edges and by working as directly below the anchorage point as possible. Move
the anchor as required or install additional anchors no more than 8 feet apart.
Work sites vary. Some lateral travel may be required. Consider swing hazards and fall clearance requirements. Consult the fall protection system
manufacturer's user instruction manual.
4.3 Installation Location: Inspect the anchor before each use according to the inspection procedure detailed in Section 7 of this manual. Consider
conditions and circumstances that could affect user safety. Select a suitable anchor location, on the field or adjacent to the peak but not right on it.
Ensure the chosen location will support the strength requirement, minimize free fall and swing hazards, as shown in Figure 3.
The competent person must develop a site plan to ensure the chosen location is a minimum 6ft. from any exposed edge, and is not on a gable,
eave, or fascia, or on rotting or decayed wood. Ensure the anchor is placed for proper load direction as shown in Figure 4.
Ensure multiple anchors are installed a minimum of 8 ft. apart. For hip roofs, install at least one anchor per hip face as shown in Figure 5. Ensure
the chosen site can provide sufficient fall clearance.
subsystems other than those described in this manual.
anchor point as this may cause a roll‐out condition and/or unintentional disengagement.
equipment, can damage equipment, cause severe injury and are potentially fatal.
WARNING
suspended loads.
3
Publicidad
Tabla de contenido
