OcCre Berlin Instrucciones De Montaje página 5

PHOTO 26. Glue the bases 64 in a centred position. Fit and glue the beams 65 into place. Between the two beams glue the
crossbar 66. Use white glue.
PHOTOS 27 to 29. Fit and glue together the parts 67, 68 and 69, to make up the support for the wheels. Insert the axle 72 and
the rings 70 and glue the wheels 73 to the ends of the axles and the washers 74. Finally glue the rings to the axle to centre the
assembly, making sure that the wheels can turn freely. Fit the assembly into place using just the screws 71 (do not glue it to the
chassis in case one day you decide to remove it in order to motorise the model).
PHOTOS 30 & 31. Glue the trim 75 to the ends of the beams 76 and 77 and glue into place, centred on the beam 78. Use quick
drying glue. Then glue these assemblies onto the beams 79, using white glue. Make sure that these parts are perfectly aligned.
Using a 1.5 mm diameter drill bit make a hole in the slots in the central beam, into which the shafts of the springs can be
inserted.
PHOTOS 32 & 33. Wind the 1 mm diameter wire round lengths of 1.5 mm wire to make up the springs 80, 81 and 82. Cut them
to size and fit them to the beams. Insert the shafts 83, 84 and 85. Attach them with washers 86 and 87. Use quick drying glue.
Paint the whole assembly metal colour.
PHOTO 34. Using quick drying glue, glue the plate springs 88 into place. Using white glue, glue the supports 89 and 90 into
place. Glue and pin the stops 91 to the washers 46, using white glue. Using quick drying glue, glue the bushing stops to the
beams. Paint the whole assembly metal colour metal.
PHOTO 35. Paint the bottom of the tram dark grey. Fit into place and glue the rolling gear. Glue on the parts 92, 93 and 94. Use
quick drying glue. Paint the fitted parts dark grey and the wheel assemblies metal colour.
PHOTOS 36 to 38. Make up the steps using the parts 95, 96 and 97. Use white glue. Paint them dark grey and glue them into
the gaps in the platforms. Join together the two parts of the supports 98 and attach them to the bumpers 99 using the pin 100
(see template). Fit and glue these parts into place. Paint them metal colour. Using quick drying glue, glue the support frame 101
(see template). Insert a ring C into the hole in the bumper, attach the chain 102. Attach the other end of the chain to an eyebolt
B and insert it into the base of the front. Paint these parts black.
PHOTO 39. Centre and glue the beams 103 and 104 at the indicated distances. Use white glue. Paint all of the roofs light grey.
PHOTO 40. Cut out and glue the lettering 105 and 106 and the lines for between the windows 107. Glue the strips 108, painted
green. Use white glue. You can paint the lines 107 green instead of cutting them out of the paper.
PHOTO 41. On one of the sides of the tram, glue the gates 109 painted green and the handrails 110. Use quick drying glue.
PHOTO 42. Glue the numbers 111 to the fronts. Use white glue. Onto one of the platforms pin an eyebolt B, at the top.
PHOTO 43. Glue the walkways 112 onto the beams. Use white glue.
PHOTO 44. Fit and glue the parts 113 and 114. On top pin and glue the part 115 to form a base for the trolley pole. Glue it to
the central part of the rooftop. Use white glue. Paint this part, and also the walkways, dark grey.
PHOTO 45. Glue the base of the trolley pole 116 to the drawbars 117 and 118. Make up a spring 119 in a similar way to the
springs made in photo 32. Insert the shaft 120 through the spring and into the base 121, in which you will have made a 1.5 mm
diameter hole. A washer 46 will close off the assembly. Use quick drying glue. Paint the whole assembly dark grey.
PHOTOS 46 & 47. Glue the trolley pole 122 to the base and to the drawbars. At the other end glue the trolley pole wheel 123.
Insert the hook 124. Paint it metal colour. Between the wheel and the hook attach the thread 125. Use quick drying glue.
Glue the base 126 to the supports 127. Glue the sign 128 in place using white glue. Attach the headlights 129 and 131 to the
supports 133 and paint them black. Glue on the decorations 130 and 132. Use white glue. Glue them to the roof using quick
drying glue.
We have prepared this model for the sole purpose of trying to ensure that you will have a good time putting together this
beautiful scale reproduction.
If you have had fun then we have achieved our aim. Thank you.
OCCRE