Peavey ICA Serie Guia De Operadores página 58

Rated Power (two channels):
200 watts @ 20 Hz - 20 kHz both
channels driven at <0.1% THD
Rated Power (one channel):
215 watts @ 1 kHz at <0.0075%
THD
Minimum Load Impedance:
ICA 400V-70: 25 ohms
ICA 400V-100: 50 ohms
Maximum RMS Voltage Swing:
ICA 400V-70: 86 volts
ICA 400V-100: 116 volts
Frequency Response:
10 Hz - 25 kHz; +0, -.3 dB at 1 watt
Power Bandwidth:
ICA 400V-70:
10 Hz - 100 kHz; +0, -3 dB at rated
power
ICA 400V-100:
10 Hz - 50 kHz; +0, -.3 dB at rated
power
THD (two channels driven):
ICA 400V-70:
<0.1% @ 200 W from 20 Hz - 20 kHz
with both channels driven
ICA 400V-100:
<0.15% @ 200 W from 20 Hz -
20 kHz with both channels driven
THD (one channel driven):
ICA 400V-70:
<0.005% @ 200 W @ 1 kHz
ICA 400V-100:
<0.015% @ 200 W @ 1 kHz
SMPTE IMD:
<0.1% 60 Hz and 7 kHz, 200 W
Slew Rate:
ICA 400V-70: 30 V/µs
ICA 400V-100: 40 V/µs
Damping Factor:
ICA 400V-70:
>1,000:1 @ 20 Hz - 400 Hz
ICA 400V-100:
>2,000:1 @ 20 Hz - 400 Hz
Due to our efforts for constant improvements, features and specifications are subject to change without notice.
ICA ™ 400V SPECIFICATIONS
Input CMRR:
> -65 dB @ 1 kHz
Voltage Gain:
x40 (32 dB)
Input Sensitivity:
ICA 400V-70:
1.77 volts for rated output
ICA 400V-100:
2.5 volts for rated output
Input Impedance:
20 k ohms, balanced
Hum and Noise:
> -110 dB, "A" weighted referenced to
rated power
Crosstalk:
ICA 400V-70:
>-70 dB, "A" weighted referenced to
rated power
ICA 400V-100:
>-65 dB, "A" weighted referenced to
rated power
Current Draw @ 1/8 power:
ICA 400V-70: 415 watts
ICA 400V-100: 385 watts
Current Draw @ 1/3 power:
ICA 400V-70: 600 watts
ICA 400V-100: 565 watts
Idle Current Draw:
ICA 400V-70:
38 watts in Standby Mode
ICA 400V-100:
43 watts in Standby Mode
Maximum Current Draw:
ICA 400V-70:
970 watts for rated power
ICA 400V-100:
840 watts for rated power
Thermal Emissions (BTU/hr.):
500 @ 1/3 power,
350 @ 1/8 power
58
Cooling:
80 mm DC fan, off until heatsinks
reach 45 o C, then variable speed
Controls:
2 rear panel attenuators, sequential
turn-on / off
Indicator LEDs:
2 Clip, 2 Signal, 2 LFC, 1 Protect,
1 Power
Protection:
Temp., DC, turn-on bursts,
subsonic, incorrect load or short
Connectors:
8-pin plugable signal input, 4-pin
plugable sequential power,
4-terminal barrier strip, IEC AC
power connector
Construction:
All steel; 16 ga. chassis, 18 ga. top,
12 ga. rack ears
Dimensions:
3.48" x 19" x 16.4"
88.4 mm x 483 mm x 416.6 mm
Gross Weight:
33.5 lbs. (15.2 kg.)
Net Weight:
31 lbs. (14 kg.)