Tylo CC 10 Instrucciones De Instalación Y Empleo página 7

SETTINGS
Note: CC 100-0B/0S only
Note: for all settings, the Tylarium should be switched OFF. To be changed
more than once: However, temperature and humidity settings can be changed
when the Tylarium is ON.
MANUAL ON/OFF.
Note: CC 100-0B/0S only
Setting the bathing temperature.
Press TEMP – the previous temperature is displayed. Use the up and down arrows
( ) to change the temperature.
Manual on/off.
Important! Don't forget to set the off time. The sauna may be switched on for a
maximum of 12 hours.
Press ON to switch the facility on. Press OFF to switch it off.
PROGRAMMING THE WEEKLY TIMER
with different settings for different days of the week.
Note: CC 100-0B/0S only
Setting on/off, temperature.
Press MENU – Use the left and right arrow keys (
programming mode using the down arrow ( ).
Use the left and right arrow keys (
to programming mode by pressing the down arrow ( ).
Choose the setting number (such as setting 1) with the left and right arrow keys (
). Shift to programming mode by pressing the down arrow ( ).
Use the up and down arrows (
the right arrow ( ). Change the minutes using the up and down arrows
( ).
To be changed more than once: Use the right arrow ( ) to move to end hour
setting and then the up and down arrows (
minutes with the right arrow ( ). Change the minutes using the up and down
arrows ( ). Shift to temperature with the right arrow ( ). Change the
temperature using the up and down arrows (
arrow ( ). Change the on/off mode using the up and down arrows (
Now the setting (Monday, setting 1) is done; press MENU to return to
programming mode. Programme the stand-by times for each day by moving to the
day/setting with the left and right arrow keys (
maximum of four time settings per day. When all settings are done, go back to
timer settings by pressing MENU twice, press ON, and the weekly settings are
activated. To be changed more than once: A red LED blinks until the sauna or
steam bath starts at a set time; after this it glows steadily (a text on the display tells
when this happens).
To switch the Tylarium off manually, press OFF. (This only switches off the current
bath).
To de-programme the weekly settings, press MENU, use the left and right arrows
( ) to shift to timer settings and press OFF.
PROGRAMMING THE WEEKLY TIMER
with the same setting for all days of the week.
Note: CC 100-0B/0S only
Setting on/off, temperature.
Press MENU – Use the left and right arrow keys (
programming mode using the down arrow ( ).
Use the left and right arrow ( ) keys to select the mode WEEK. Shift to
programming mode by pressing the down arrow ( ).
Select the setting number (for example, setting 1) using the left and right arrow
keys ( ).
Use the down arrow ( ) to move the programming mode, then use the up and
down arrows ( ) to set the start hour. Shift to minutes with the right arrow ( ).
Change the minutes using the up and down arrows (
Shift to end time setting using the right arrow ( ), then use the up and down
arrows ( ) to change the end time, then shift to minutes with the right arrow ( ).
Change the minutes using the up and down arrows (
with the right arrow ( ). Change the temperature using the up and down arrows (
). Shift to on/off with the right arrow ( ). Change the on/off mode using the up
and down arrows ( ).
Now the setting (1) is done; press MENU to return to programming mode.
Programme each setting using the left and right arrow keys (
can be programmed to switch on and off four times a day. When all settings are
done, go back to timer settings by pressing MENU twice, press ON, and the
weekly settings are activated. A red LED blinks until the sauna or steam bath starts
at a set time; after this it glows steadily (a text on the display tells when this
happens).
To switch the Tylarium off manually, press OFF. (This only switches off the current
bath).
To de-programme the weekly settings, press MENU, use the left and right arrows
( ) to shift to timer settings and press OFF.
STAND-BY PROGRAMMING
with different settings for different days of the week.
Note: CC 100-0B/0S only.
Press MENU – Use the left and right arrow keys (
Start programming mode using the down arrow ( ).
) to set the timer. Start
) to set the day (for example, Monday). Shift
) to set the start hour, then shift to minutes with
) to set the end hour. Shift to
). Shift to on/off with the right
). You can programme a
) to set the timer. Start
).
). Shift to temperature
). The Tylarium
) to set the stand-by timer.
Use the left and right arrow keys (
to programming mode by pressing the down arrow ( ).
Use the up and down arrows (
the right arrow ( ). Change the minutes using the up and down arrows
( ).
To be changed more than once: Switch to end time setting using the right arrow
( ), use the up and down arrows (
with the right arrow ( ). Change the minutes using the up and down arrows (
Shift to temperature with the right arrow ( ). Change the temperature using the up
and down arrows (
mode using the up and down arrows (
Now the stand-by setting (Monday, setting 1) is done; press MENU to return to
programming mode. Programme the stand-by time for each day. When all settings
are done, go back to stand-by settings in the MENU ON, and the stand-by settings
are activated. A red LED blinks until the sauna or steam bath starts at a set time;
after this it glows steadily (a text on the display shows that the panel is in a stand-
by position and when it will switch on).
As soon as you press ON, the temperature increases to the pre-set bathing
temperature. After 1 hour, the facility resumes the stand-by temperature. Each time
the ON button is pressed, a new 1-hour bathing period starts.
Note: if both the timer time and stand-by time are set to be on at the same time, the
timer function takes over.
To switch the Tylarium off manually, press OFF. (This only switches off the current
bath).
To be changed more than once: To de-programme the stand-by settings, press
MENU, use the left and right arrows (
press OFF.
To restart with the same settings, press MENU, go to stand-by using the left and
right arrows (
NOTE: Always block with a password after Standby programming.
STAND-BY PROGRAMMING
with the same setting for all days of the week.
Note: CC 100-0B/0S only.
Press MENU – Use the left and right arrow keys (
Start programming mode using the down arrow ( ).
Use the left and right arrow (
programming mode by pressing the down arrow ( ).
).
Use the up and down arrows (
the right arrow ( ). Change the minutes using the up and down arrows (
To be changed more than once: Switch to end time setting using the right arrow
( ), use the up and down arrows (
with the right arrow ( ). Change the minutes using the up and down arrows
( ). Shift to temperature with the right arrow ( ). Change the temperature using
the up and down arrows (
on/off mode using the up and down arrows (
Now the stand-by time is programmed in. Go back to stand-by programming by
pressing MENU twice, press ON. A red LED blinks until the sauna or steam bath
starts at a set time; then it glows steadily (a text on the display tells that the panel is
on stand-by and when it will switch on).
As soon as you press ON, the temperature increases to the pre-set bathing
temperature. After 1 hour, the facility automatically resumes stand-by temperature.
Each time you press ON, 1 hour's bathing time begins.
Note: if both the timer time and stand-by time are set to be on at the same time, the
timer function takes over.
To switch the Tylarium off manually, press OFF. (This only switches off the current
bath).
To be changed more than once: To de-programme the stand-by settings, press
MENU, use the left and right arrows (
OFF.
To restart with the same settings, press MENU, go to stand-by using the left and
right arrows (
NOTE: Always block with a password after Standby programming.
Password.
Setting the password.
Press MENU – Use the right and left arrows (
programming mode by pressing the down arrow ( ). Enter the code using all the
arrow keys (
use the left arrow key () to change the code. Set the new code using all the arrow
keys (
MENU. Now the password is activated.
To return to unlocked mode, repeat the above procedure but set on/off to off.
Note: Do all other settings before setting the password.
BATHING OUTSIDE OF THE PROGRAMMED TIME
if the panel is locked with a password.
The sauna or steam bath can be used at a different time than the programmed time.
Press ON to start a one-hour bathing period. To extend the bath, press ON again.
The facility automatically switches off one hour after the last time ON was pressed.
In the event of any problems, please contact the retailer
where you purchased the equipment.
© This publication may not be reproduced, in part or in whole, without the written permission of Tylö. Tylö
reserves the right to make changes in materials, construction and design.
) to set the day (for example, Monday). Shift
) to set the start hour, then shift to minutes with
) to set the end hour, then shift to minutes
). Shift to on/off with the right arrow ( ). Change the on/off
).
) to shift to the stand-by setting and
), and press ON.
) keys to select the mode WEEK. Shift to
) to set the start time, then shift to minutes with
) to set the end hour, then shift to minutes
). Shift to on/off with the right arrow ( ). Change the
).
) to shift to the stand-by setting and press
), and press ON.
). After power failure, the code is reset to 1995). Press MENU,
). Press MENU. Activate on/off with the right arrow ( ), press
).
) to set the stand-by timer.
).
) to go to password setting. Start
7