Denon AVC-A11SR Instrucciones De Operación página 12

ENGLISH
Setting the Subwoofer mode
1
Select the subwoofer mode.
UNING
BAND M E
TUNING
2
Enter the setting.
ENTER / SHIFT
The System Setup Menu reappears.
SELEC
NOTES:
• The subwoofer mode functions only when the input signal is Dolby Digital or a DTS digital signal.
— Assignment of low frequency signal range —
• The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or
DTS signals) and the low frequency signal range of channels set to "Small" in the setup menu. The low
frequency signal range of channels set to "Large" are produced from those channels.
— Subwoofer mode —
• The subwoofer mode setting is only valid when "Large" is set for the front speakers and "Yes" is set for
the subwoofer in the "Speaker Configuration" settings (see page 10).
• When the "LFE+MAIN" playback mode is selected, the low frequency signal range of channels set to
"Large" are produced simultaneously from those channels and the subwoofer channel.
In this playback mode, the low frequency range expand more uniformly through the room, but depending
on the size and shape of the room, interference may result in a decrease of the actual volume of the low
frequency range.
• Selection of the "LFE - THX" play mode will play the low frequency signal range of the channel selected
with "Large" from that channel only. Therefore, the low frequency signal range that are played from the
subwoofer channel are only the low frequency signal range of LFE (only during Dolby Digital or DTS signal
playback) and the channel specified as "Small" in the setup menu. THX is recommended in this play mode
so that bass interference is less likely to occur in the room.
• Select the play mode that provides bass reproduction with body.
Setting the THX Surround EX / DTS-ES Source Auto
Set the operation for the digital signals when playing in the 6.1 SURROUND, DTS-ES and THX SURROUND EX
surround modes.
1
At the System Setup Menu select "SB CH
UNING
Auto Flag Detect" and press the ENTER
ENTER / SHIFT
button.
BAND MODE
SELEC
TUNING
2
Select the desired setting.
TUNING
When set to "ON", the
BAN M E
operation for software for
TUNING
which no identification
signals are recorded is set.
12
3
Enter the setting.
ENTER / SHIFT
The System Setup Menu reappears.
SELEC
THX surround EX/DTS ES Auto Flag Detect Mode (AFDM) setting
ON ................This function only works with software on which a special identification signal is recorded.
This software is scheduled to go on sale in the future.
This is a function for automatically playing in the 6.1-channel mode using the surround back
speakers if the software is recorded in THX Surround EX or DTS-ES or in the normal 5.1-
channel mode without using the surround back speakers when the software is not recorded
in THX Surround EX or DTS-ES.
OFF...............Set the "OFF" mode to perform 6.1-channel playback with conventional 5.1-channel sources
or sources on which the identification signal described below is not recorded.
Non-Flag Source SB ch Output setting
THX surround EX/DTS ES ..Playback is conducted using the surround back speaker.
Surround back channel is reproduced using digital matrix processing.
Non MTRX....Playback is conducted using the surround back speaker. The same signals as those of the
surround channels are output from the surround back channel.
OFF...............Playback is conducted without using the surround back speaker.
NOTES:
• The "SB CH Auto Flag Detect" setting screen is displayed when the surround back speaker is set to
"Large" or "Small" at "Speaker Configuration".
• The surround back speakers can also be turned on and off using the "SB CH OUT" surround parameter.
(See page 34.)
Select the setting according to the program source to be played.
Setting the delay time
• Input the distance between the listening position and the different speakers to set the delay time for the
surround mode.
• The delay time can be set separately for surround speakers A and B.
Preparations:
Measure the distances between the listening position and the speakers
(L1 to L5 on the diagram at the right).
L1: Distance between center speaker and listening position
L2: Distance between front speakers and listening position
L3: Distance between surround speakers and listening position
L4: Distance between surround back speakers and listening position
L5: Distance between subwoofer and listening position
1
At the System Setup Menu select "Delay Time".
TUNING
BAND MODE
TUNING
2
Switch to the Delay Time screen.
ENTER / SHIFT
SELEC
FL Center FR
Subwoofer
L
L
1
2
Listening position
L
5
L
L 4
SL SR
3
SBL SBR