Preset Memory - Denon AVC-A11SR Instrucciones De Operación

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 163
ENGLISH

Preset memory

By using the preset memory, the included remote control unit can be used to control other makes of video
equipment. Note that this is not possible for some models, however. In such cases, use the learning function
(see page 19) to store the remote control signals in the remote control unit's memory.
See page 20 for instructions on resetting the data stored in the preset memory.
1
Press the power ON/SOURCE button and the
OFF button at the same time.
• "SET UP" appears on the remote control
unit's display.
ON /
OFF
SOURCE
2
Press the ENTER button.
ENTER / SH FT
SELEC
3
Use the D and H cursor buttons to display
"ENTER CODE" on the remote control unit,
then press the ENTER button.
The remote control unit's display switches
as follows each time the D and H cursor
buttons are pressed.
ENTER CODE
TUNING
CODE NO
BAND
MODE
TUNING
LEARN
SYS CALL
ENTER / SHIFT
RESET
SELEC
4
After "SEL DEVICE" is displayed, the last
selected mode is set. Use the D and H cursor
buttons to display the component whose codes
you want to store in the memory, then press
the ENTER button.
TUNING
ENTER / SH FT
BAND
MODE
SELEC
TUNING
The display switches as shown below each
time the D and H cursor buttons are
pressed.
TV
CD
MD
TAPE
VDP
DVD
CABLE
DBS
VCR3
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental
operation, cover the remote control unit's transmitting window while setting the preset memory.
• Depending on the model and year of manufacture, this function cannot be used for some models, even if
they are of makes listed on the included list of preset codes.
• Some manufacturers use more than one type of remote control code. Refer to the included list of preset
codes to change the number and check.
18
1
3, 4
2, 3, 4
5
5
Referring to the included List
1
2
3
of Preset Codes, use the
4
5
6
number buttons to input the
preset
code
7
8
9
number) for the manufacturer
0
of the component whose
signals you want to store in
the memory.
6
"OK" is displayed when the signals are
registered and the mode is terminated.
7
To store the codes of another component in the
memory, repeat steps 1 to 6.
VCR1
VCR2
The preset codes are as follows upon shipment from the factory and after resetting:
TV, VCR .......................................................HITACHI
CD, MD, TAPE, CDR, VDP, DVD.................DENON
DBS.............................................................GENERAL INSTRUMENT
CABLE.........................................................JERROLD
Checking the preset memory settings
1
Press the power ON/SOURCE button and the
OFF button at the same time.
• "SET UP" appears on the remote control
unit's display.
ON /
OFF
SOURCE
2
Press the ENTER button.
ENTER / SHIFT
SELEC
3
Use the D and H cursor buttons to display
"CODE NO" on the remote control unit, then
press the ENTER button.
UNING
ENTER / SHIFT
BAND
MODE
SELEC
TUNING
Operating a component stored in the preset memory
1
Press the mode selector button for the
component you want to operate.
(a
4-digit
NOTE:
• For the DVD player remote control buttons,
function names may differ depending on the
make. Compare with the remote control
operation of the various components.
4
Press the D and H cursor
UNING
buttons to display the registered
preset memory on the remote
BAND
MODE
control unit's display and check.
TUNING
5
Press the ENTER button to
ENTER / SHIFT
terminate.
SELEC
1

Publicidad

Tabla de contenido
loading

Tabla de contenido