Tabla de contenido
Publicidad
TABLE OF CONTENTS
INTROdUCTION
Receiving and Uncrating . . . . . . . . . . . . . . . . . . . .2
How to Order Replacement Parts . . . . . . . . . . . . .2
SAfETY INfORMATION . . . . . . . . . . . . . . . . 3
Support Installation . . . . . . . . . . . . . . . . . . . . . . . .4
Ceiling Hanger Installation . . . . . . . . . . . . . . . . . .4
Conveyor Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . .4
Racked Sections . . . . . . . . . . . . . . . . . . . . . . . .4, 5
Electrical Equipment . . . . . . . . . . . . . . . . . . . . . . .5
Conveyor Start-Up. . . . . . . . . . . . . . . . . . . . . . . . .5
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5, 6
drive Chain Alignment and Tension . . . . . . . . . . .6
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . .6
Maintenance Checklist . . . . . . . . . . . . Back Cover
190-NSP Parts drawings . . . . . . . . . . . . . . . . . . .7
190-NSP Parts List . . . . . . . . . . . . . . . . . . . . . . . .8
190-NSPC 90° Parts drawings . . . . . . . . . . . . . . .9
190-NSPC 90° Parts List. . . . . . . . . . . . . . . . . . .10
190-NSPC 60° Parts List. . . . . . . . . . . . . . . . . . .10
190-NSPC 60° Parts drawings . . . . . . . . . . . . . .11
190-NSPC 45° Parts drawings . . . . . . . . . . . . . .12
190-NSPC 45° Parts List. . . . . . . . . . . . . . . . . . .13
190-NSPC 30° Parts List. . . . . . . . . . . . . . . . . . .13
190-NSPC 30° Parts drawings . . . . . . . . . . . . . .14
190-NSPS 45° Parts List. . . . . . . . . . . . . . . . . . .15
190-NSPS 45° Parts drawings . . . . . . . . . . . . . .16
190-NSPS 30° Parts List. . . . . . . . . . . . . . . . . . .17
190-NSPS 30° Parts drawings . . . . . . . . . . . . . .18
190-NSPSS 45° Parts List . . . . . . . . . . . . . . . . .19
190-NSPSS 30° Parts List . . . . . . . . . . . . . . . . .19
190-NSPSS 45° Parts drawings . . . . . . . . . . . . .20
190-NSPSS 30° Parts drawings . . . . . . . . . . . . .21
Spanish Version . . . . . . . . . . . . . . . . . . 22
INTRODUCTION
This manual provides guidelines and procedures for installing,
operating, and maintaining your conveyor. A complete parts list
is provided with recommended spare parts highlighted in gray.
Important safety information is also provided throughout the manual.
for safety to personnel and for proper operation of your conveyor, it
is recommended that you read and follow the instructions provided
in this manual.
• Receiving and Uncrating
1. Check the number of items received against the bill of lading.
2. Examine condition of equipment to determine if any damage
occurred during shipment.
3. Move all crates to area of installation.
4. Remove crating and check for optional equipment that may be
fastened to the conveyor. Make sure these parts (or any foreign
pieces) are removed.
NOTE: If damage has occurred or freight is missing,
Contact your Hytrol Integration Partner.
• How to Order Replacement Parts
Included in this manual are parts drawings with complete replacement
parts lists. Minor fasteners, such as nuts and bolts, are not
included.
When ordering replacement parts:
1. Contact dealer from whom conveyor was purchased or nearest
HYTROL Integration Partner.
2. Give Conveyor Model Number and Serial Number or HYTROL
factory Order Number.
3. Give Part Number and complete description from Parts List.
4. Give type of drive. Example-8" End drive, 8" Center drive, etc.
5. If you are in a breakdown situation, tell us.
Hytrol Conveyor
Company, Inc.
JONESBORO, ARKANSAS
SERIAL #
HYTROL Serial Number
(Located near drive on Powered Models).
2
Model
Model
XX
123456
Publicidad
Capítulos
Tabla de contenido
