Programming Menu Items; Powersave Mode; Updating Firmware - Hatco Toast-Qwik TQ3-500 Serie Manual De Instalación Y Operación

OPERATION

Programming Menu Items

Use the following procedure to change or create custom menu
item settings.
1. Touch and hold the desired menu item on the Menu Screen
for three seconds.
• The Programming
will appear showing a list of
programmable settings.
Heat
Top Heat:
level from top
Setting range is
1 = lowest heat/lightest toast.
100 = highest heat/darkest toast.
Btm Heat: Heat output level from bottom elements.
Setting range is 1–100%. 1 = lowest heat/lightest toast.
100 = highest heat/darkest toast.
Time: Total time product is in toasting chamber.
Increasing belt time will slow down conveyor and create
darker product. Decreasing belt time will speed up
conveyor and create lighter product.
2. Touch the or arrow next to the desired setting to
change the setting.
3. To change the menu item picture, touch the picture. A
screen will appear with the available pictures
a. Touch the desired picture. The touchscreen will return to
the Programming screen and show the new picture.
4. To change or edit the menu item name, touch the name. A
keypad screen will appear.
a. Touch the key to delete the current name.
b. Use the keypad to change or update the menu item
name.
c. Touch the key to save the name and return to the
Programming screen.
5. When all programming is done, touch the
to the Menu screen.

PowerSave Mode

All TQ3 series toasters have a built-in PowerSave mode.
This feature significantly reduces heat levels and energy
consumption when the toaster has not been used for a specified
period of time or when activated by the operator.
To start PowerSave mode manually during operation:
1. Touch the icon on the Menu screen.
• The conveyor belt will speed up
temporarily to clear product from
toaster.
• The PowerSave screen will show
on the touchscreen.
To exit PowerSave mode:
1. Touch the icon on the PowerSave screen. The unit will
be ready to toast immediately.
NOTE: During recovery from PowerSave mode, the ColorGuard
system will slow down the conveyor speed for consistent
toast color. Full conveyor speed will be achieved in
approximately 10 minutes, depending on how much the
heat output level of the elements was reduced during
PowerSave mode.
screen
Top Heat
75 %
Btm Heat
75 %
output
Toast Time 75 sec
elements.
1–100%.
icon to return
Powersave Mode
press the leaf
to exit

Updating Firmware

Use the following procedure to upload
firmware updates to the toaster from an
external USB drive.
1. Follow the "Startup" procedure
listed previously in this section.
2. Touch the
Screen. A password screen will
Name
appear.
• Enter the 3-digit password "248".
The Service screen will appear.
3. Touch FIRMWARE on the Service
screen. The Update Select screen
will appear.
4. Touch FIRMWARE on the Update
Select screen. The Firmware
Update screen will appear.
5. Slide the cover to the side, and
insert the USB drive into the USB
port.
• The USB port is on the front of
the unit, underneath and to the
right of the touchscreen.
6. Touch UPDATE.
• T h e f i r m w a r e
w i l l b e g i n
approximately 30 seconds
(a progress bar will appear).
NOTICE: Do not remove the
USB drive or turn off the unit
during a software update.
• When the update is complete, the unit will restart and
the Logo screen will appear for a few seconds showing
the new firmware version.
7. Remove the USB drive from the USB port, and slide the
cover back to cover the port.
10
Touchscreen
Control
icon on the Menu
USB Port
Service
Firmware
Control
Testmode
Version
u p d a t e
Firmware Update
a n d l a s t
Plug-in the USB stick then
press the Update button.
Form No. TQ3CEM-0618
Cover
Usage
PowerSave
Exit
Firmware
Image
Exit
Update
Exit