Kärcher B 150 R 75 Manual Del Usuario página 13

DANGER
Danger of tipping if gradient is too high.
The gradient in the direction of trav-

el should not exceed 10% (Adv
15%).
Drive only lengthwise on uphill and

downhill gradients, do not turn.
Danger of tipping when driving round
bends at high speed.
Danger of slipping on wet floors.
Drive slowly when cornering.

Danger of tipping on unstable ground.
Only use the machine on sound

surfaces.
Danger of tipping with excessive side-
ways tilt.
Driving
Take the seating position.

Plug in the Intelligent Key.

Bring the safety switch into the "1"

position.
Set programme selector switch to

transport run.
Set the drive direction using the

drive direction button at the opera-
tor console.
Determine the driving speed by

pressing the drive pedal.
Stop the machine: Release the

drive pedal.
NOTICE
The drive direction can also be
changed during the drive. Thus, very
blunt edges can be polished by moving
forward and backward a few times.
Overload
In case of overloading, the drive motor
automatically switches off after a cer-
tain period. A fault message is dis-
played on the console. The concerned
unit gets switched off if the controls get
overheated.
Allow machine to cool down at least

for 15 minutes.
Turn the programme switch to

"OFF", wait for a short period of
time and turn it back to the desired
programme.
Filling in detergents
Detergent
ATTENTION
Risk of damage. Only use the recom-
mended detergents. With respect to
different detergents the operator bears
the increased risk regarding the opera-
tional safety and danger of accident.
Only use detergents that are free from
solvents, hydrochloric acid and hydro-
fluoric acid.
Follow the safety instructions for using
detergents.
Note
Do not use highly foaming detergents.
Recommended detergents:
Application
Routine cleaning of all
water resistant floors
Routine cleaning of
glossy surfaces (e.g.
granite)
Routine cleaning and
basic cleaning of indus-
trial floors
Routine cleaning and
basic cleaning of fine
stoneware tiles
Routine cleaning of tiles
in sanitary areas
Cleaning and disinfec-
tion in sanitary areas
Removal of coating
from all alkali-resistant
floors (e.g. PVC)
Removal of coating
from linoleum floors
Fresh water
Open the cover of the fresh water

reservoir.
Fill fresh water (max. 60 °C) until 15

mm below the upper edge of the
tank.
Pour in detergent.

NOTICE
If detergent is added to the cleaning
detergent tank first, followed by water,
there could be a lot of foam.
Close the cover of the fresh water

reservoir.
NOTICE
Fill up the fresh water tank completely
before starting up the machine to ven-
tilate the water supply system.
Filling system (optional)
Connect the water hose to the con-

nection neck on the filling system.
Open the water supply.

Once the maximum fill level is
reached, the built-in floater valve
will stop the water inflow.
Shut off water supply.

Remove the water hose.

Setting the parameters
With yellow Intelligent Key
Parameters for the different cleaning
programmes are preset in the appli-
ance.
11
-
EN
Depending on the authorisation of the
yellow Intelligent Key, individual pa-
rameters can be changed.
The modification of the parameters is
only valid until another cleaning pro-
Detergent
gramme is selected via the programme
RM 746
selection switch.
RM 780
If you wish to permanently change the
parameters, you must use a grey Intel-
RM 755 es
ligent Key. This adjustment procedure
is described in the section "Grey Intel-
ligent Key".
RM 69
Note:
ASF
Almost all displayed text regarding pa-
rameter adjustment is self-explanato-
ry. The only exception is the parameter
RM 753
FACT:
Fine Clean: Lower brush speed for
–
removing the grey film on fine stone
RM 751
floors.
Whisper Clean: Medium brush
–
speed for regular cleaning with re-
RM 732
duced noise level.
Power Clean: High brush speed for
–
RM 752
polishing, crystallising and sweeping.
Turn the program selection switch

to the desired cleaning program.
RM 754
Turn the info button until the de-

sired parameter is displayed.
Press Info button - the set value

blinks.
Set the desired value by turning the

info button.
Confirm the changed setting by

pressing the Info button or wait till
the set value is automatically ac-
cepted after 10 seconds.
Setting the Vacuum Bar
Oblique position
To improve the vacuuming result on
tiled floors the vacuum bar can be
turned to an oblique position of up to
5°.
Release the wing nuts.

Turn the vacuum bar.

Tighten the wing nuts.

Inclination
If the vacuum result is unsatisfactory
the inclination of the straight vacuum
bar can be modified.
Adjust the rotary handle to incline

the suction bar.
13