General Information - Beninca BILL4024 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 14
ENG
GENERAL INFORMATIONS
The product shall not be used for purposes or in ways other than those for which the product is intended for and as described in this manual.
Incorrect uses can damage the product and cause injuries and damages.
The company shall not be deemed responsible for the non-compliance with a good manufacture technique of gates as well as for any de-
formation, which might occur during use. Keep this manual for further use.
INSTALLER GUIDE
This manual has been especially written to be use by qualified fitters. Installation must be carried out by qualified personnel (professional
installer, according to EN 12635), in compliance with Good Practice and current code. Make sure that the structure of the gate is suitable
for automation. The installer must supply all information on the automatic, manual and emergency operation of the automatic system and
supply the end user with instructions for use.
GENERAL WARNINGS
Packaging must be kept out of reach of children, as it can be hazardous. For disposal, packaging must be divided the various types of
waste (e.g. carton board, polystyrene) in compliance with regulations in force. Do not allow children to play with the fixed control devices of
the product. Keep the remote controls out of reach of children. This product is not to be used by persons (including children) with reduced
physical, sensory or mental capacity, or who are unfamiliar with such equipment, unless under the supervision of or following training by
persons responsible for their safety. Apply all safety devices (photocells, safety edges, etc.) required to keep the area free of impact, crushing,
dragging and shearing hazard. Bear in mind the standards and directives in force, Good Practice criteria, intended use, the installation en-
vironment, the operating logic of the system and forces generated by the automated system. Installation must be carried out using safety
devices and controls that meet standards EN 12978 and EN 12453. Only use original accessories and spare parts, use of non-original spare
parts will cause the warranty planned to cover the products to become null and void. All the mechanical and electrical parts composing
automation must meet the requirements of the standards in force and outlined by CE marking.
ELECTRICAL SAFETY
An omnipolar switch/section switch with remote contact opening equal to, or higher than 3mm must be provided on the power supply mains.
Make sure that before wiring an adequate differential switch and an overcurrent protection is provided.
Pursuant to safety regulations in force, some types of installation require that the gate connection be earthed. During installation, maintenance
and repair, cut off power supply before accessing to live parts. Also disconnect buffer batteries, if any are connected. The electrical installation
and the operating logic must comply with the regulations in force. The leads fed with different voltages must be physically separate, or they
must be suitably insulated with additional insulation of at least 1 mm. The leads must be secured with an additional fixture near the terminals.
During installation, maintenance and repair, interrupt the power supply before opening the lid to access the electrical parts
Check all the connections again before switching on the power. The unused N.C. inputs must be bridged.
WASTE DISPOSAL
As indicated by the symbol shown, it is forbidden to dispose this product as normal urban waste as some parts might be harmful for en-
vironment and human health, if they are disposed of incorrectly. Therefore, the device should be disposed in special collection platforms
or given back to the reseller if a new and similar device is purchased. An incorrect disposal of the device will result in fines applied to the
user, as provided for by regulations in force.
Descriptions and figures in this manual are not binding. While leaving the essential characteristics of the product unchanged, the manufacturer reserves
the right to modify the same under the technical, design or commercial point of view without necessarily update this manual.
1) INTRODUCTION
Electromechanical operator to activate swing gates, available in the following model:
BILL4024: with motor powered at 24 VDC.
The RIGHT (DX) version is also available to install the system on the right gate leaf, and the LEFT (SX) version is available for installation on the left gate leaf.
In case of doubt, as shown in the instruction manual, the wording DX (right) or SX (left), which identifies the different models, can be seen by opening
the release handle.
For simplicity reasons, this manual shows the SX motor for left gate leaves. For the DX (right) versions, installation dimensions and instructions are the same.
The main dimensions are shown in Fig. 1.
• Before installing the system, read the instruction herein.
• It is mandatory not to use the BILL4024 item for applications different from those indicated in the instructions herein.
• Supply the end user with instructions for using this system.
• The end user should receive special instruction manual.
• All Benincà items are covered by an insurance policy for damages and injuries caused by manufacture faults. It is however required that the machine
bear the CE marking and original Benincà parts be used.

2) GENERAL INFORMATION

To ensure a good operation of these automatic devices, the gate to be automated should meet the following requirements:
- good strength and stiffness.
- hinges should have a minimum backlash and allow for smooth and regular manual operations.
- when closed, the gate leaves should correctly overlap for their entire height.
Warning: BILL4024 is not equipped with electric limit switches or mechanical stoppers. It is mandatory that the gate leaf be equipped with mechanical
stoppers fitted to the ground (Fig.2 ref. A and B).
8
WARNING

Publicidad

Tabla de contenido
loading

Tabla de contenido