Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V
25 (7.6)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More
not
American Wire gauge
Than
More
Than
0
6
18
6
10
18
10
12
16
12
16
14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. Tools are factory tested; if this
tool does not operate, check power supply.
COMPONENTS (FIG. A)
WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.
Polarized Plug
To reduce the risk of electric shock, this equipment has a
polarized plug (one blade is wider than the other). This
equipment must be used with a suitable polarized 2 wire or
3 wire extension cord. Polarized connections will fit together
only one way. Make sure that the receptacle end of the
extension cord has large and small blade slot widths. If the
plug does not fit fully into the extension cord, reverse the
plug. If it still does not fit, obtain a suitable extension cord. If
the extension cord does not fit fully into the outlet, contact
6
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
16
16
14
16
14
12
16
14
12
12
Not Recommended
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
a qualified electrician to install the proper outlet. Do not
change the tool plug or extension cord in any way.
Intended Use
Your heat gun has been designed for stripping paint,
soldering pipes, shrinking PVC, welding and bending
plastics as well as general drying and thawing purposes.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
The heat gun is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Switch (Fig. B)
The position of the switch controls both the fan speed and
the heat output of the gun.
•
To turn the tool on in low speed, low heat, depress the
side of the switch
1
marked "I".
•
To turn the tool on in high speed, high heat, depress the
side of the switch marked "II".
•
To turn the tool off, return the switch to the middle
position marked "O".
Fig. B
1
Temperature Adjustment Knob (Fig. C)
1. To raise the air temperature, turn the knob
2. To lower the air temperature turn the
knob counterclockwise.
5
clockwise.
Publicidad
Tabla de contenido
