Tabla De Contenido; Main Features; Installation; Part Names And Functions - Denon DN-X400 Instrucciones De Operación

- TABLE OF CONTENTS -
z
Main features .....................................................5
x
Installation ..........................................................5
c
Part names and functions ..............................5, 6
v
Connections........................................................7
b
Fader start ..........................................................8
• ACCESSORIES
Please check to make sure the following items are included with the main unit in the carton:
q Operating instructions .......................................1

MAIN FEATURES

1
CONGRATULATIONS! You have purchased the
DENON DN-X400 DJ mixer from DENON.
1. CH. Fader and Crossfader start
The CD player can be started or stopped simply by
increasing or decreasing the level of the CH fader
or by using the cross fader left to right or right to
left. (This function can only be used when the
DENON CD players DN-1800F, DN-2100F or DN-
2600F is connected to the DN-X400.)
2. Digital outputs
The DN-X400 allows you to record directly to CD-R,
MiniDisc or a hard disk device through it's exclusive
coaxial and optical digital outputs.
The digital outputs maintains a constant 16 bit / 44.1
kHz signal.
3. Track mark
Track numbers can be added at any position during
recording onto a digital recorder using the DN-
X400's digital outputs.
4. Enhanced input/output terminals (Analog)
8 Line, 2 Phono, 2 microphone systems, 2 Main
outputs, Booth/Zone output, Sub woofer output
and Rec output are provided independently. Effect
in/out terminals are also provided for a external
effects processor.

INSTALLATION

2
When the DN-X400 is mounted inside a coffin or DJ
booth, we recommend leaving a 3 cm blank space
above the mixer if possible.
n
Track mark ..........................................................9
m
PFL (Pre Fader Level) .........................................9
,
Replacing the crossfader....................................9
.
Specifications .....................................................9
w Connection cords (3.5 mm stereo mini cord) .....2
5. 3-Band equalizer/Gain
Bass, Mid, Treble and Gain controls are available on
every input channel.
6. Crossfader contour
This feature allows adjusting the "shape" of the
Crossfader response from a gentle curve for
smooth, long running fades, to the steep pitch
required for top performance cut and scratch
effects.
7. Mic post
This feature will pass the Main Mic signal into the
Booth/Zone, Rec output and Digital output signal
path.
In the OFF mode, the Main Mic signal will not be
routed through the above outputs.
8. PFL (Pre Fader Level)
This feature provides a means to adjust the input
level gain of each channel to avoid over loading. By
making this adjustment in advance will insure a
smooth transistion between cross fades or channel
fades.
L/CUE
LINE1 LINE3 PHONO1/LINE5 PHONO2/LINE7
-20 -15 -10 -7 -5 -3 -1 0 +1 +3 +5 +8 PWR
R/PGM
0 10 ON/OFF MIN MAX MIN MAX MIN MAX MIN MAX
LEVEL GAIN LINE2 GAIN LINE4 GAIN LINE6 GAIN LINE8
MIC POST MASTER
1 2 3 4
+10dB +10dB +10dB +10dB 10 10
-12dB +12dB ON/OFF -26dB -26dB -26dB -26dB 0 10
HI HI 10 HI 10 HI 10 HI 10 LEVEL EFFECT
8 8 LOOP
METER
8 8 8 8
6 6 MAIN
+10dB 6 +10dB 6 +10dB 6 +10dB 6
4 4
-12dB +12dB MAIN MIC -26dB -26dB -26dB -26dB BOOTH
MID MID 4 MID 4 MID 4 MID 4
/ZONE 2 2
2 2 2 2 MIC
0 0
+10dB 0 +10dB 0 +10dB 0 +10dB 0
-12dB +12dB -26dB -26dB -26dB -26dB
LOW LOW LOW LOW LOW
CH FADER START CH FADER START CUE
CROSS CROSS
FADER FADER
START A DIGITAL OUT TRACK START B
MARK
0 10 ON/OFF
LEVEL CH 1 CH 2 CH 3 CH 4
AUX MIC
L-CUE
F/S F/S MONO R-PGM
1 2 3 1 2 3
A B
OFF 4 OFF 4
ON OFF
CUE PGM STEREO 0 10
CH FADER START PAN CUE/PGM LEVEL
ASSIGN A ASSIGN B PHONES
CROSSFADER
CONTOUR

PART NAMES AND FUNCTIONS

3
(1) Front Panel
q
MAIN MIC EQ controls
• Contour the frequency response of the Main
Mic input -12 dB to +12 dB.
HI
• Adjusts high-tone Main Mic sound -12 dB to
+12 dB.
At the center position, sound is flat.
MID
• Adjusts mid-tone Main Mic sound -12 dB to
+12 dB.
At the center position, sound is flat.
LOW
• Adjusts low-tone Main Mic sound -12 dB to
+12 dB.
At the center position, sound is flat.
w
MAIN MIC level control
• Adjusts the level of the Main Mic input.
e
MAIN MIC ON/OFF button
• Puts the Main Mic signal into the Main outputs
signal path.
• When the button is pressed, the Main Mic is
on and the adjacent orange indicator lights.
r
MIC POST ON/OFF button
• Puts the Main Mic signal into the Booth/Zone,
Rec and Digital out signal path.
• When the button is pressed, the adjacent
green indicator lights.
t
AUX MIC level control
• Adjusts the level of the Aux Mic input.
y
AUX MIC ON/OFF button
• Puts the Aux Mic signal into the mixer signal
path.
• When the button is pressed, the Aux Mic is on
and the adjacent orange indicator lights.
u
Source EQ controls
• Contour the frequency response of the
selected inputs.
HI
• Adjusts the high-tone sound -26 dB to +10 dB.
At the center position, sound is flat.
MID
• Adjusts the mid-tone sound -26 dB to +10 dB.
At the center position, sound is flat.
LOW
• Adjusts the low-tone sound -26 dB to +10 dB.
At the center position, sound is flat.
NOTE:
Clipping may occur if adjustments are set to
harsh.
i
GAIN level control
• Adjusts the level of the selected input -∞ to
+10 dB.
ENGLISH
o
Source input select switch
• Selects either a Phono/Line or Line input for
the source.
!0
TRACK MARK button
• The track number is switched when this
button is pressed during recording onto a
digital recorder using the digital outputs.
!1
Source input fader (Ch. fader)
• Controls the level of the selected Input.
!2
BOOTH/ZONE level control
• Adjusts the level of the Booth/Zone outputs.
!3
BOOTH/ZONE METER button
• When this button is pressed down and held,
the meter indicates the stereo level in the
LEFT and RIGHT meter output. The adjacent
green indicator lights.
!4
MASTER LEVEL fader
• Adjusts the level of the Main outputs. Signals
from the channels selected with the Assign
switches will be output using the Source input
fader (Ch. fader) and the Crossfader, while
signals from other channels will be outputs
using the Source input fader (Ch. fader).
!5
Peak dB CUE/PROGRAM meter
• Displays the output level following Master
Level adjustment, the peak level is held for 1
second.
Display range : -20 dB to +8 dB.
• Can switch between two display mode. See
below @0 .
!6
EFFECT LOOP MAIN button
• Routes the Main signal through the external
processor attached to the EFFECT connectors
on the rear.
• When the button is pressed in, the adjacent
orange indicator lights. (When the processor
isn't attached,indicator blinks.)
!7
EFFECT LOOP MIC button
• Routes the Main Mic signal through the
external processor attached to the EFFECT
connectors on the rear.
• When the button is pressed in, the adjacent
orange indicator lights. (When the processor
isn't attached,indicator blinks.)
NOTE:
When the Effect Loop Main and Mic are on,
the signal of Mic is output to all the outputs
regardless of setting the Main Mic and the
Post Mic.
!8
HEADPHONE output jack
• Accepts 1/4" stereo headphone plugs.
!9
HEADPHONE level control
• Adjusts the volume for the headphones.
5