Usb; Functions With Easy Access; Max/Min Values; Other Viewing Options - Full Gauge V.03 Manual De Instrucciones

If you want to force sampling by temperature, humidity or pressure variation, it can be configured in the
Recording" "Humidity variation to Force Data Recording" ,
"Overwrite Data Memory" you can configure the controller to rewrite or not the oldest data when the internal memory is full. If you choose
this parameter, the
Humitech Super
procedure overwrites old data to preserve the newest data. If you choose
internal memory end is reached. This preserves old data however the new data is lost. When datalogger operation is stopped, the controller displays
an "out of memory" message.
"Datalogger Operation Mode"
By configuring the parameter
ON, always OFF or to be manually turned ON.
Data stored in internal memory can be accessed through serial communication or USB port, and they can be viewed through the SITRAD
supervision software.
The data stored in the internal memory will be deleted only by the SITRAD supervision software.

9.11 - USB

USB port allows you to connect a flash drive and do the following:
Humitech Super's
- Download the data stored in the internal memory;
- Read parameter recipes;
- Save current parameters in a recipe.
By connecting the USB device, the controller will display a menu with the options above. Select the option you want by pressing the
keys and press to confirm.
Download the data stored in the internal memory:
By choosing this option, the controller saves the internal memory data in a file in the flash drive. If the data had already been downloaded on the
same day in the same flash drive, the controller displays a message saying that the file already exists in the USB device. Users may opt to overwrite
the file or rename the controller to save this new data (
Do not remove the USB flash drive during data transfer.
Read parameter recipes:
By selecting this option, the controller will upload a recipe stored in the flash drive. Then a list of all the recipes stored in the flash drive will be
displayed. Press and to select a file and press
Do not remove the USB flash drive during data transfer.
Save current parameters in a recipe:
By selecting this option, the controller will save a recipe with the controller parameters in the flash drive. If a given recipe is already in the flash drive,
the controller will display a message indicating that the file already exists in the USB device. Users may choose to rewrite the file (
cancel the operation ( key). Do not remove the USB flash drive during data transfer.

10 - FUNCTIONS WITH EASY ACCESS

10.1 - Max/Min Values

Press the key to view the minimum and maximum temperature values. Two situations may occur depending on the Humitech Super operation:
If the current operation mode is
turned ON.
If the operation mode is "Program Mode"
navigate through the 132 possible days of the program. Each day has its respective minimum and maximum temperature values stored.
Press to exit this viewing mode.
Manual and OFF Mode (Press1x
Temperature
25.5 @ 31.5 #
Minimum

10.2 - Other Viewing Options

For switching between other viewing options pres
Main Screen
Main screen (manual mode)
Average
temperature
TM:25.4# H:40.0
SP :10.0#
Manual Temperature Setting (Setpoint)
will record new data at the beginning of the memory every time the memory end is reached. This
, you can use the access functions to the operator to set the Datalogger to be always
key) or cancel recording (
to confirm.
"Manual Mode" , the controller directly displays the minimum and maximum temperature since the controller was
, the controller first displays the initial date of day count and by pressing the
)
Maximum
until the desired selection is displayed. The viewing option screens will scroll as follows:
All Temperatures Other Measures
Humidity
%
and "Pressure Variation to Force Data Recording"
"No" , the
Humitech Super
®
key).
Programming Mode (Press 2x
Program Day
Temper. day003
25.5 @ 31.5 #
Minimum Maximum
Operation Mode
Operation mode (manual mode)
Current operation mode
Manual Mode
SP:10.0#
Manual Temperature Setting (Setpoint)
41
"Temperature Variation to Force Data
. By using the selection
"Yes"
stops datalogger operation every time
key) or to
and keys you can
)
Datalogger Status
for
®
and