Peltor TacticalPro MT15H7 Serie Manual Del Usario página 4

CONGRATULATIONS ON AN EXCELLENT CHOICE!
The Peltor Tactical Pro is an active hearing protector that allows comfortable contact with your surroundings while ef-
fectively protecting you from harmful noise.
The Peltor Tactical Pro has separate full stereo through double microphones for ambient noise, plus amplifiers and earphones
in the cups. The electronic system allows you to listen to an external audio signal, such as a com radio, at the same time.
The headset is tested and approved according to PPE directive 89/686/EEC and EMC directive 89/336/EEC, which
means that it meets the demands for CE marking.
To ensure complete satisfaction with your new Peltor product, please read the entire instruction manual.
(A) WHAT IS WHAT?
1a. Extra broad headband (MT15H7A) with soft padding for ideal comfort throughout the working day.
1b. Neckband (MT15H7B) for use when a headband would be in the way.
1c. Helmet attachment (MT15H7P3*) for all regular helmet types. Peltor's helmets, visor and rain protector fit this
helmet attachment.
1d Collapsible headband F. Thin band for use with the band snug over the top of the head.
2. Individually sprung headband wires of stainless steel provide an even distribution of pressure around the ears.
They maintain their resilience better than regular plastic headbands through a wide range of temperatures.
3. Low, two-point fasteners and easy height adjustment with no protruding parts.
4. Soft, wide foam/fluid-filled ear cushions with built-in pressure-relief canals for low pressure, effective sealing and
ideal comfort.
5. On/off button. A tone in the earphones confirms the activity. The Peltor Tactical Pro switches off automatically two
hours after the last sound is registered. Two tones in close succession warn you that the unit will be
switched off in one minute if youdo not adjust the volume.
6. Volume control. Buttons for adjusting the volume level in the headphones. Press the upper button to increase the
volume and the lower button to decrease it. The last setting is stored when the unit is switched off.
7. The battery cover with locking screw makes battery replacement quick and easy.
8. Microphones for ambient noise, which is reproduced at no more than 82 dBA equivalent noise level in the ear
phones.
9. Audio input for connecting a communication radio, etc.
WARNING! The external input does not have an automatic volume limit. You must manually adjust the noise level
on the external equipment to the maximum input signal as defined in diagram (G).
10. The speech microphone (on some models only) allows two-way communication by com radio or telephone. An
adapter is required.
ASSEMBLY/CONFIGURATION
Batteries
Unscrew the locking screw and open the battery cover. Use two 1.5-volt AA batteries (included).
Make sure that the + and – poles of the battery are in the correct position (see the figure in the cover). WARNING! If you
use rechargeable batteries, install them only according to the charger manual. Dry-cell batteries can explode if recharged.
Three tones are emitted every 30 seconds in the event of low battery power. The unit switches off automatically after five
minutes. Never replace batteries with the unit switched on.
Setting
(B) Headband: (B:1) Slide out the cups and place the headset over your ears so that the ear cushions enclose the ears
completely and fit snugly against the head.
(B:2) Adjust the height of the cups for a comfortable fit while holding the headband flat against your head.
(B:3) The headband should lie across the top of the head.
(C) Helmet attachment: (C:1) Snap the helmet attachment into the slot on the helmet. To switch the unit from ventilation
to working position, press the headband wires inwards until you hear a click on both sides. Ensure that the cup and the
headband wires in working mode do not bump or snag on anything so that noise leakage can occur.
Note: The cups can be set in three positions: (C:2) working position, (C:3) ventilation position and (C:4) parking position
(D) Neckband
(D:1) Adjust the cups so that the ears are completely surrounded by the ear cushions.
(D:2) Adjust the height using the headband until you have a snug, comfortable fit.
(D:3) The headband should lie across the top of the head.
IMPORTANT! For the best protection, brush aside hair around the ears so the ear cushions
Spectacle frames should be as thin as possible and fit close to the head.
(E) Collapsing the collapsible headband:
(E:1) Press the cups all the way in.
(E:2) Collapse the headband. Make sure there are no creases in the ear cushions and that they lie snugly against one
another. For instructions for use, see the Headband section.
2