Install Hood - Broan ALLURE QS3 Serie Manual De Instrucciones

INSTALL HOOD

KEYHOLE (4)
1 Hang hood from (4) Mounting Screws. Slide hood towards
wall until mounting screws are engaged in narrow end of (4)
Keyholes. Tighten mounting screws securely. A long
screwdriver works best.
2 Replace bottom cover.
3 Connect ductwork to hood. Use Duct Tape to make joints
secure and air tight.
4 Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16,
40 W Maximum Incandescent Bulbs. Purchase bulbs
separately.
!
CAUTION:
Bulbs may be hot! Refer to bulb packag-
ing for further information.
5 Replace filters, turn on power at service panel, and test for
proper operation.
®
MOUNTING SCREW (4)
PAR20,
50W MAX.
HALOGEN
BULB (2)
- or -
R16,
40W MAX.
INCANDESCENT
BULB (2)
OPERATION
Fan: 4 push button switches. Push any button to select one of the
four fan speeds. Push the same button to turn fan off. Press an-
other button to change fan speed. A light above each fan button
indicates the fan speed.
Lights: Press "on/off" button and lights will come on at their previ-
ous light level. Press button again to turn lights off. To increase light
level, press the "+" button. To reduce light level, press the "-" but-
ton. There are 3 light levels to select.
Delay Off: While fan is running, press the "delay" button to allow
the fan to run for 10 minutes and then turn itself off.
Filter Change Indicator: After replacing the cleaned, or new fil-
ters, press the "filter" button to turn off the indicator light.
Heat Sentry System: Your range hood is equipped with an ad-
vanced Heat Sentry system.
The advanced Heat Sentry system monitors temperature and au-
tomatically adjust the fan to the appropriate setting.
1) If the fan is on, the Heat Sentry system will increase the fan
setting when the temperature is elevated. If the temperature con-
tinues to rise, the Heat Sentry system will continue to increase
the fan setting until the temperature is stabilized or reduced. The
flashing light above the fan button shows the Heat Sentry sys-
DUCT
tem fan setting. Once the temperature has reduced, the Heat
TAPE
Sentry system will change the fan to the original setting.
2) If the fan is on or off, the Heat Sentry system will automatically
turn the fan on at its highest speed when the temperature is above
normal. When the Heat Sentry system is on, the light above the
fan button B (Boost) will flash on and off. After the temperature
has lowered to normal, the fan will change to the setting prior to
the Heat Sentry turning on.
CLEANING
WARNING: To reduce the risk of electric shock,
disconnect from power supply before cleaning.
Aluminum mesh filters: Clean frequently using hot water and a
mild detergent. Filters are dishwasher safe.
Charcoal filters: Clean filter surfaces frequently with a damp cloth
and a mild detergent. DO NOT immerse filters in water or put in
dishwasher. The special "Clean Sense" feature indicates when the
filter is to be replaced. The blue and yellow strips will blend to green
when it is time to change the filter. The "Clean Sense" feature works
best when facing toward the cooking surface.
To clean hood: Remove filters. Use a damp cloth and a mild de-
tergent to wipe all grease-laden surfaces. Read the Silverstone
label on the bottom cover. It has instructions for care and cleaning
of the Silverstone
- it must not become bent or misaligned. DO NOT ALLOW WATER
TO ENTER MOTOR. Make sure all surfaces are completely dry
before re-installing filters and restoring power.
Motor is permanently lubricated. Do not oil or disassemble motor.
ALLURE
®
surface. Use care when cleaning blower wheel
®
QS3 SERIES
RANGE HOOD
Page 5
®