Technical Data - Martin Yale intimus 007SL Instrucciones De Uso

GB
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
COMPENSATION OF THE LIGHT BARRIER:
In order to eliminate malfunctions due to chan-
ging light conditions at the inlet aperture (e.g.
by changing the location) or due to the wear
of the fotocell (scratches), the sensitivity of the
light barrier is automatically re-adjusted by the
machine for the detection of „normal" paper in
regular intervals.
This so called „compensation" can also be carried
out manually in accordance with the sequence
described in the following (e. g. after change of
the light barrier or the PC Board).
The „receptacle full" switch-off must not be ac-
tivated for the re-adjustment. The procedure is
as follows:
1. Switch off the maschine at the rocker switch
(1) and open the door.
2. Press the pushbutton switch „reverse" (4) and
keep it pressed.
3. Press the „ready" rocker switch (1).
4. Release the „reverse" pushbutton switch (4)
after approx. 3 sec.
5. Push switching flap „receptacle full" backwards
for at least 3 sec.
6. Close the door after approx. 3 sec.
7. Cover the light barrier with a piece of paper (do
not feed the paper up to the cutter) and wait
until the motor is switched on.
This completes the compensation. The machine
is now ready for operation.
Note: If the compensation process has been
interfered with due to exessive external incident
light (direct sun light, lamps, spots etc.) or due to
a false procedure, keep the external light away
from light barrier and re-start the compensation
process right from the beginning.
SPECIAL ACCESSORIES
Description
Plastic bag, 700 x 500 x 1200 x 0,06 mm
Lubrication bottle, 125 ml
Second deposit tray cpl., silver gray
Second deposit tray cpl., chrome plated
Note: For orders of special accessories and spare parts, please contact your dealer.
All manuals and user guides at all-guides.com
<< Danger of injury! Keep all
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
MAINTENANCE
CLEANING THE PHOTOCELLS:
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes" of the photocell with a brush.
MAINTENANCE CUTTING BLOCK:
After approximately 15 minutes of con-
tinuous use, run the cutting system in
reverse for 15 to 20 seconds and spray
some of the enclosed Special Oil onto the
cutting system.
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched
off over night (rocker switch (1) (fig. 1).
DISPOSING
DISPOSING OF THE MACHINE:
Dispose of
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
PAPER JAM:
loose articles of clothing, ties, If too much paper is fed to the cutting system the
machine will react as follows:
jewelery,longhairorotherloose
- The cutting system blocks and then stops.
objects away from opening!
- The pilot lamp of the stop-putton „S" (3) (fig. 2)
will light.
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(4) (fig. 2).
- The cutting mechanism then runs backwards
and returns the excess material.
- Remove excess paper from the machine and
continue shredding with less paper.
Important: After any paper jam, make certain
the cutting mechanism is free to operate in both
free (particles have jammed between the cutters
and the scraper), spray some of the special oil
supplied with the machine through the feed slot
onto the cutting mechanism while alternating
between forward and reverse modes until the
machine is free.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the machine off with
the rocker switch (1) (fig. 1).
Allow the motor to cool down for 15 to 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- is the plug connected to the mains?
- is the rocker switch (1) on?
- is the door closed?
- is the receptacle full?
The receptacle has to be emptied.
- is there a paper jam?
Follow the instructions under „paper jam".
- has the motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
Cutting width:
007SL:
007SF:
Cutting capacity:
007SL:
007SF:
Working width:
007SL:
the machine in an
007SF:
Power consumption:
Supply voltage:
Pre-fusing:
230V/50Hz:
240V/50Hz:
120V/60Hz:
Order-No.
100V/50/60Hz:
99954
Dimensions (WxDxH):
99943
Noise level:
30712
Weight:
30702
007SL:
007SF:
* Capacity may vary depending upon paper weight, grain and power.
5
MALFUNCTION

TECHNICAL DATA

0,65x1,5–5 mm
(cross-cut)
0.8x4.5 mm
(cross-cut)
10–12 sheets *
8–10 sheets *
300 mm
380 mm
2 kW
230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
16 A
13 A
20 A
20 A
700x550x1115 mm
approx. 70 dB(A)
approx. 170 kg
approx. 142 kg