Important Safety Notes - Martin Yale MY 3000SC Instrucciones De Uso

GB

IMPORTANT SAFETY NOTES

<< The machine may not be operated by
more than one person at any given time!
The machine was designed for safe
operation by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Keep children away from the machine.
This machine's design and safety concept
are based on adult dimensions (feeder
route, safety cut-off switches, etc.) to ensure
that it can be operated safely by adults
only.
<< Repairs may only be performed by
trained personnel.
CONTROLS:
1 = Pushbutton switch „ready" (fig. 1)
Depress this switch to start the machine or to
stop the machine.
2 = Rocker switch (fig. 1)
(forward / reverse)
This switch is for the following functions:
- " " position
The cutting system operates.
- " " position
The cutting system runs in reverse.
3 = Light barrier (forward running) (fig. 2)
The shredding operation starts as soon as
material is fed into one of the two feed slots.
4 = Pilot lamp „ready" (fig. 1)
Lights when the pushbutton switch (1) is
operated.
5 = Pilot lamp "material jam" (fig. 1)
Lights if too much material is fed into the
cutting mechanism. The cutting mechanism
halts, then runs one step in reverse and
stops. The motor switches off.
fig. 1
All manuals and user guides at all-guides.com
<< Keep all loose articles of
<< Never insert fingers into opening.
Serious injury may result!
<< In case of danger switch the
STOP machine off with the mains switch,
or with the emergency switch, or
unplug the machine.
<< Always unplug the machine from
the mains power supply before
opening the machine.
OPERATION
6 = Pilot lamp "motor overload" (fig. 1)
Lights up if the motor is overloaded. The
machine cannot be started again until the
motor has cooled down.
7 = Pilot lamp (fig. 1)
„receptacle missing"
Lights up when the receptacle is not placed
properly under the machine. The machine is
switched off automatically when the
receptacle is removed and cannot be startet
if the receptacle is not placed properly under
the machine.
8 = Pilot lamp
„receptacle full" / „reverse" (fig. 1)
a) Model MY3000CC
Lights when the receptacle is full and needs
to be emptied. At the same time the
machine switches off automatically.
b) Model MY3000SC
Lights up when the cutting system is
switched to reverse running.
The shredder may not be used as a
step ladder or as a seat. Danger of
falling due to breakage!
MATERIAL FEED:
- Switch on the machine at the pushbutton switch
4
(1) (fig. 1). The pilot lamp (4) (fig. 1) lights up.
5
6
7
8
2
3
1
fig. 2
SCOPE OF APPLICATION:
clothing, ties, jewelery, The MY3000SC / MY3000CC data shredder is
long hair or other loose
designed for shredding general printed material
objects away from and data media such as CDs, DVDs and credit
opening, injury may cards.
result!
INSTALLATION:
- Unpack and set machine upright.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA").
- Feeding paper
Feed the paper into the cutting system through
the paper feed slot (9) (fig. 2).
Note: when shredding transparencies, the
machine should be switched manually to the
forward running position (rocker switch (1) (fig. 1)
to position " ".
- Feeding data media
Feed the data media (CDs, DVDs or credit
cards) into the cutting system one by one through
the separate security feed slot (10) (fig. 2).
- The machine automatically switches to forward
running and pulls the material in. The machine
switches off again automatically when shredding
is completed.
RECEPTACLE FULL INDICATOR (Fig. 3)
When the shredded material becomes visible in
the "receptacle full" window (11) (fig. 3) it is time to
empty the receptacle.
Model MY3000CC
10
Additional indication functions:
Before the maximum bin level is reached at which
the machine switches off, a beep will sound up to
three times to indicate that it is time to empty the
receptacle.
9
When the receptacle is full, the machine switches
off. The pilot lamp (8) (fig. 1) lights up.
4
MY 3000 SC
MY 3000 CC
INITIATION
This machine should only be used for
shredding paper and credit cards and
for shredding CDs and DVDs.
Any attempt to shred other types of data
medium may result in damage to the
machine (e.g. destruction of the cutting
mechanism etc.).
The socket outlet shall be installed
near the equipment and shall be easily
accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
OPERATION
Never feed the shredder with a quantity
of material exceeding the maximum
indicated. Refer to the TECHNICAL
DATA section.
Should the machine become overloaded,
follow the instructions under "MATERIAL
JAM IN MACHINE"
"MALFUNCTIONS".
under