Starting The Programme; Child Lock - Saivod LST1261 Manual Del Usuario

Auxiliary function selection
Select the desired auxiliary functions before
starting the programme. Furthermore, you can also
select or cancel auxiliary functions that are suitable
to the running programme without pressing the
Start / Pause / Cancel button when the machine is
operating. For this, the machine must be in a step
before the auxiliary function you are going to select
or cancel.
If the auxiliary function cannot be selected or
canceled, light of the relevant auxiliary function will
blink 3 times to warn the user.
Some functions cannot be selected together.
C
If a second auxiliary function conflicting with
the first one is selected before starting the
machine, the function selected first will be
canceled and the second auxiliary function
selection will remain active.
An auxiliary function that is not compatible
C
with the programme cannot be selected. (See
"Programme and consumption table")
Auxiliary Function buttons may vary according
C
to the model of the machine.
• Prewash
A Prewash is only worthwhile for heavily soiled
laundry. Not using the Prewash will save energy,
water, detergent and time.
As their meshed texture causes excessive
C
foaming, wash the veils/tulle by putting little
amount of detergent into the main wash
compartment. Do not put detergent in the
prewash compartment.
• Rinse Plus
This function enables the machine to make
another rinsing in addition to the one already made
after the main wash. Thus, the risk for sensitive
skins (babies, allergic skins, etc.) to be effected by
the minimal detergent remnants on the laundry can
be reduced.
• Rinse Hold
If you are not going to unload your clothes
immediately after the programme completes, you
can use rinse hold function to keep your laundry
in the final rinsing water in order to prevent them
from getting wrinkled when there is no water in the
machine.
In models equipped with Spin Speed Adjustment
button, select the Spin Speed and press Start
/ Pause / Cancel button if you want to spin the
laundry held in water.
In models not equipped with Spin Speed
Adjustment button, select Spin+Pump programme
if you want to spin your laundry held in water.
In these models, you need to stop the
C
machine by pressing Start / Pause / Cancel
button before switching to spin step and after
pump step is completed and the water in the
machine is drained. Thus, water inside the
machine is drained and your laundry is not
spun.
• No Heat
Use this function if you want to wash your laundry
in cold water.
• No Spin
Use this function if you do not want your clothes
be spun at the end of the programme.
• Spin speed reduction
This function allows spinning of laundry at a
speed lower than the maximum spin speed of the
machine.
When Spin Reduction button is pressed, spin
speed will be limited to the minimum speed
specified on the control panel.

Starting the programme

Press Start / Pause / Cancel button to start the
programme. Start / Pause / Cancel button lights
up to indicate that the programme has started.
Loading door is locked and Loading Door light
turns off.

Child Lock

Use Child Lock function to prevent children from
tampering with the machine. Thus you can avoid
any changes in a running programme.
You can switch on and off the machine with
C
On / Off button when the Child Lock is active.
When you switch on the machine again,
programme will resume from where it has
stopped with the child lock enabled.
To activate the Child Lock:
Press and hold 1
buttons for 3 seconds simultaneously after
washing programme has started. The 1
Function light flashes continuously.
To deactivate the Child Lock:
Child lock must be deactivated to start a new
programme after the programme has finished or to
interrupt a running program.
Press and hold 1
buttons for 3 seconds simultaneously to disable
child lock.
Progress of programme
Progress of a running programme can be followed
from the Programme Follow-up indicator. At
the beginning of every programme step, the
relevant indicator light will turn on and light of the
completed step will turn off.
To change the auxiliary function, speed and
temperature settings while a program is running,
you need to switch the machine to Pause mode.
Press Start / Pause / Cancel button to switch the
machine into Pause mode. In this case, Start /
Pause / Cancel light flashes.
If the machine does not pass to the spinning
C
step, Rinse Hold function might be active
or the automatic unbalanced load detection
system might be activated due to the
unbalanced distribution of the laundry in the
machine.
12
EN
and 2 Auxiliary Function
st nd
and 2 Auxiliary Function
st nd
Auxiliary
st