Noise And Vibrations; Handling Information; Packing Lifting And Transport; Checks Upon Delivery - Comet CRS 90 BT Manual De Instrucciones

• Do not place tools on top of the batteries: they may
cause a short-circuit or an explosion.
• When using battery acid, rigorously respect the
relative safety instructions. In the presence of parti-
cularly strong magnetic fields, evaluate the possible
effect on electronic control devices.
Never spray water on the machine to clean it.
☞ Recovered fluids contain detergents, disinfectants,
water, as well as organic and inorganic material colle-
cted during work operations: dispose of them in accor-
dance with current legal provisions.
• If the machine malfunctions and/or operates ineffi-
ciently, turn it off immediately (disconnecting it from
the electric power supply or from the batteries) and do
not tamper with it.
Contact one of the manufacturer's technical service
centres.
• All maintenance or accessory replacement operati-
ons must be carried out in environments with adequ-
ate lighting and only after having disconnected the
machine from the electric power supply by detaching
the battery connector.
• All work on the electrical system and all mainte-
nance and repair operations (especially those not
explicitly described in this manual) should be carried
out only by authorized service centers or by speciali-
zed technical personnel who are experts in the sector
and in the pertinent safety regulations.
☞ The machine owner can only use original acces-
sories and spare parts supplied exclusively by the
manufacturer since such parts are the only ones that
guarantee that the equipment will operate safely wit-
hout any problems. Do not use parts disassembled
from other machines or other kits as spare parts.
☞ Before each use, check the machine and, in particu-
lar, check that the battery charging cable and the con-
nector are in good condition and safe for use. If they
are not in perfect condition, do not use the machine
for any reason until an authorized specialist repairs the
defective parts.
☞ If foam or liquid is noted, immediately turn off the
suction motor.
☞ Do not use the machine on textile flooring, such as
rugs, carpeting, etc.
Wax, foaming detergents or dispersions along the
hoses may cause serious problems for the machine or
clog the hoses.
3.2

NOISE AND VIBRATIONS

For informations relating to noise and vibration data
see last page.

4. HANDLING INFORMATION

4.1

PACKING LIFTING AND TRANSPORT

• During all lifting or transport operations, make sure
that the packed machine is securely anchored to pre-
vent it from tipping over or falling accidentally.
Transport vehicle loading and unloading operations
must be carried out with adequate lighting.
The packed machine must be handled using adequate
devices, making sure not to damage/strike any part of
the packing, not to tip it over and to be very careful
when placing it on the ground.
☞ All these instructions also apply to the batteries and
the battery charger.
4.2

CHECKS UPON DELIVERY

☞ When the goods are delivered (machine, battery
or battery charger) by the transporter, carefully check
the condition of the packing and its contents. If the
contents have been damaged, notify the transporter
and reserve the right, in writing (select the word
"reserve" on the document), to submit a claim for
compensation before accepting the goods.
4.3

UNPACKING

• Wear safety clothing and use adequate tools to
limit the risks of accidents.
Carry out the following steps if the machine is packed
with a cardboard housing:
- Use scissors or clippers to cut and eliminate the plas-
tic straps.
- Slip off the cardboard housing from the top of the
packed machine.
- Remove the envelops inside and check their contents
(use and maintenance manual, battery charger con-
nector)
- Remove the metallic brackets or plastic straps that
secure the machine to the pallet.
- Release the brushes and the squeegee from the pa-
cking.
- Take the machine off the pallet (pushing it backward)
by using an inclined surface that is solidly attached to
the floor and to the pallet.
If the machine is packed in a wooden crate:
- Detach all the wooden sides from the pallet, starting
from the top one.
- Remove the protective film wrapped around the ma-
chine.
- Remove the metallic brackets or plastic straps that
secure the machine to the pallet.
- Release the brushes and the squeegee from the pa-
cking.
- Take the machine off the pallet (pushing it backward)
by using an inclined surface that is solidly attached to
the floor and to the pallet.
Take the same precautions and follow the same inst-
ructions to remove the optional battery charger from
33