3M 7500 Serie Instrucciones página 5

2078 Particulate Filter, P95, 3M recommended ozone
protection
acid gas relief
2091 07000 Particulate Filter, P100
2291 Advanced Particulate Filter, P100
2096 Particulate Filter, P100, with nuisance level acid
gas relief
2296 Advanced Particulate Filter, P100, with nuisance
level acid gas relief
2097 07184 Particulate Filter, P100, 3M recommended for
ozone protection
relief
2297 Advanced Particulate Filter, P100, 3M
recommended for ozone protection
level organic vapor relief
5N11 Particulate Filter, N95
5P71 07194 Particulate Filter, P95
7093 Particulate Filter, P100
7093C 37173 Particulate Filter, P100, hydrogen fluoride with
nuisance level organic vapor/acid gas relief
**** AAD part numbers are catalog numbers only. NIOSH approved as PSD part numbers
3M recommended for relief against nuisance levels of acid gases or organic vapors. Nuisance level refers to concentrations not exceeding OSHA
1
PEL or applicable government occupational exposure limits, whichever is lower. Do not use for respiratory protection against acid gases or organic
vapors.
3M recommended for ozone protection up to 10 times the OSHA PEL or applicable government occupational exposure limits, whichever is lower.
2
NOTE: Not NIOSH approved for use against ozone.
3M™ Particulate Filters must be immediately changed when an increase in breathing resistance is noticed.
In Brazil, the 3M™ Filter 5935BR is approved as a NIOSH N95 filter and as a BMOL P3 filter. It can be used with the Filter Adaptor 603 and the Filter
Retainer 501 on the 3M™ Half Facepiece 7500 Series.
ASSEMBLY INSTRUCTIONS
3M™ Cartridge 6000 Series, Filter 7093, Cartridge/Filter 7093C
1. Align cartridge notch with arrow on facepiece, as shown, and push together (Fig. 1).
2. Turn cartridge clockwise to stop (1/4 turn) (Fig. 2).
3M™ Filter 5N11 and 5P71
1. Place filter into 3M™ Retainer 501 *(07054) so printed side of filter faces the cartridge (Fig. 3).
2. Press cartridge into filter retainer. It should snap securely into filter retainer. When correctly installed, filter should completely cover face of cartridge.
3. To replace filter, remove retainer by lifting on TAB.
3M™ Filter 2000 Series
1. Align opening of filter with filter attachment on facepiece.
2. Turn filter clockwise until it is firmly seated and cannot be further turned. Repeat for second filter.
3M™ Filter Adapter 502 Assembly and Filter Attachment
1. Align adapter over cartridge. Engage front snap by squeezing front of cartridge and adapter together, placing thumbs of both hands over top of
adapter and fingers along bottom sides of cartridge (Fig. 4).
2. Engage back snap by squeezing back side of cartridge and adapter together using the same hand positions (Fig. 5). An audible click should be
heard as each snap is engaged.
3. Place filter onto the filter holder so that filter comes into even contact with gasket. Twist clockwise a quarter turn until it is firmly seated and filter
cannot be turned further. Repeat for second filter.
NOTE: The 3M™ Filter Adapter 502, once installed on a 3M™ Cartridge 6000 Series, is not to be removed or reused. Removal or reuse may
result in leakage, overexposure, sickness or death.
3M™ Filters, 2000 Series and 7093/7093C with 3M™ Filter Adapter 502
Place filter onto the filter holder so that filter comes into even contact with gasket. Twist clockwise one quarter, turn until it is firmly seated and filter
cannot be turned further. Repeat for second filter.
NOTE: The 3M™ Filter Adapter 502, once installed on a 3M™ Cartridge 6000 Series, is not to be removed or reused. Removal or reuse may
result in leakage, overexposure, sickness or death.
3M™ Filter Adapter 603 and Filters 5N11 or 5P71
1. Align notch on edge of 603 adapter with facepiece mark as shown (Fig. 22).
2. Turn adapter 1/4 turn clockwise to stop. To remove adapter, turn 1/4 turn counterclockwise (Fig. 23).
3. Place filter into 501 retainer with filter printing facing towards the 603 adapter. Snap together and ensure the filter seal is free from creases or gaps
(Fig. 24).
In Brazil, the 5935BR Filter used with the 603 adaptor is assembled following the same procedures as the 5N11 and 5P71.
, with nuisance level organic vapor/
2
1
1
1
, nuisance level organic vapor
2
1
1
, nuisance
2
1
5